Graco FinishPro II 395 PC Скачать руководство пользователя

Страница: 7 / 52

Warnings

334730F

ELECTRIC SHOCK HAZARD

This equipment must be grounded

Improper grounding, setup, or usage of the

system can cause electric shock.

•

Turn off and disconnect power cord before servicing equipment.

•

Connect only to grounded electrical outlets.

•

Use only 3-wire extension cords.

•

Ensure ground prongs are intact on power and extension cords.

•

Do not expose to rain. Store indoors.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can

cause serious chemical reaction and equipment rupture. Failure to follow this

warning can result in death, serious injury, or property damage.

•

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated

hydrocarbon solvents or fluids containing such solvents.

•

Do not use chlorine bleach.

•

Many other fluids may contain chemicals that can react with aluminum. Contact

your material supplier for compatibility.

MOVING PARTS HAZARD

Moving parts can pinch, cut, or amputate fingers and other body parts.

•

Keep clear of moving parts.

•

Do not operate equipment with protective guards or covers removed.

•

Pressurized equipment can start without warning. Before checking, moving, or

servicing equipment, follow the

Pressure Relief Procedure

and disconnect all

power sources.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on

skin, inhaled, or swallowed.

•

Read SDSs to know the specific hazards of the fluids you are using.

•

Store hazardous fluid in approved containers, and dispose of it according to

applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent

serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.

This protective equipment includes but is not limited to:

•

Protective eyewear, and hearing protection.

•

Respirators, protective clothing, and gloves as recommended by the fluid and

solvent manufacturer.

BURN HAZARD

Equipment surfaces and fluid that is heated can become very hot during operation.

To avoid severe burns:

•

Do not touch hot fluid or equipment.

CALIFORNIA PROPOSITION 65

This product contains a chemical known to the State of California to cause cancer,

birth defects or other reproductive harm. Wash hands after handling.

Содержание FinishPro II 395 PC





















































Результаты поиска

Содержание FinishPro II 395 PC

Отзывы:

Похожие инструкции для FinishPro II 395 PC

Бренды по названию

Популярные бренды

Graco FinishPro II 395 PC, Операция, Запчасти

Результаты поиска

Содержание FinishPro II 395 PC

Отзывы:

Похожие инструкции для FinishPro II 395 PC

Бренды по названию

Популярные бренды