Graco FinishPro II 395 PC Скачать руководство пользователя

Страница: 5 / 52

Warnings

334730F

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or

explode. To help prevent fire and explosion:

•

Do not spray flammable or combustible materials near an open flame or sources

of ignition such as cigarettes, motors, and electrical equipment.

•

Paint or solvent flowing through the equipment is able to result in static electricity.

Static electricity creates a risk of fire or explosion in the presence of paint or

solvent fumes. All parts of the spray system, including the pump, hose assembly,

spray gun, and objects in and around the spray area shall be properly grounded

to protect against static discharge and sparks. Use Graco conductive or

grounded high-pressure airless paint sprayer hoses.

•

Verify that all containers and collection systems are grounded to prevent static

discharge. Do not use pail liners unless they are anti-static or conductive.

•

Connect to a grounded outlet and use grounded extensions cords. Do not use

a 3-to-2 adapter.

•

Do not use a paint or a solvent containing halogenated hydrocarbons.

•

Do not spray flammable or combustible liquids in a confined area.

•

Keep spray area well-ventilated. Keep a good supply of fresh air moving through

the area.

•

Sprayer generates sparks. Keep pump assembly in a well ventilated area at least

20 feet (6.1 m) from the spray area when spraying, flushing, cleaning, or

servicing. Do not spray pump assembly.

•

Do not smoke in the spray area or spray where sparks or flame is present.

•

Do not operate light switches, engines, or similar spark producing products in the

spray area.

•

Keep area clean and free of paint or solvent containers, rags, and other

flammable materials.

•

Know the contents of the paints and solvents being sprayed. Read all Safety

Data Sheets (SDS) and container labels provided with the paints and solvents.

Follow the paint and solvents manufacturer’s safety instructions.

•

Fire extinguisher equipment shall be present and working.

Содержание FinishPro II 395 PC





















































Результаты поиска

Содержание FinishPro II 395 PC

Отзывы:

Похожие инструкции для FinishPro II 395 PC

Бренды по названию

Популярные бренды

Graco FinishPro II 395 PC, Операция, Запчасти

Результаты поиска

Содержание FinishPro II 395 PC

Отзывы:

Похожие инструкции для FinishPro II 395 PC

Бренды по названию

Популярные бренды