background image

Graco Limited Warranty

3A4803A

41

Graco Limited Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing 

its name to be free from defects in material and workmanship on the date of sale to the original purchaser 

for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, 

for a period of twelve months from the date of sale, repair or replace any part of the equipment 

determined by Graco to be defective. This warranty applies only when the equipment is installed, 

operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, 

damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or 

improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. 

Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco 

equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper 

design, manufacture, installation, operation or maintenance of structures, accessories, equipment or 

materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an 

authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco 

will repair or replace free of charge any defective parts. The equipment will be returned to the original 

purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material 

or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of 

parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR 

IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY 

OF FITNESS FOR A PARTICULAR PURPOSE

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. 

The buyer agrees that no other remedy (including, but not limited to, incidental or consequential 

damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential 

loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the 

date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH 

ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED 

BY GRACO

. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, 

etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with 

reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from 

Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other 

goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or 

otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, 

notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or 

indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du 

présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, 

donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures 

concernées.

Содержание 3A4803A













































Отзывы: