Graco 25M081 Скачать руководство пользователя | Manualshive

Страница: 21 / 32

background image

Schematics

3A5202G

21

Mixing Shaft Factory Configuration

The factory configuration of the mix shaft assembly works well for most common, pump-grade stucco materials. The
configuration of the shaft can be changed if an alternate configuration is desired.

For most materials, it is recommended to reduce starting torque by positioning the pointed ends of the mixing
elements so that they are on the leading edge. However, for very thin materials, positioning some or all of the mixing
elements so that the blunt ends are on the leading edge may improve the mix quality.

* The mix shaft retainer has a left-handed thread to ensure it does not disassemble during operation. To loosen
retainer, rotate clockwise.

WLD

240

120

WLD

*

*

«
...
19
20
21
22
23
...
»

Содержание 25M081

































Отзывы:

Нет отзывов

Похожие инструкции для 25M081

Бренд: ABB Страницы: 86

Бренд: Rangevision Страницы: 31

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Obdstar Страницы: 10

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Xo Страницы: 59

Бренд: Falcon Страницы: 8

Бренд: ICP DAS USA Страницы: 45

Бренд: Jet Страницы: 12

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: Lafayette Страницы: 10

Бренд: WARPP Страницы: 28

Бренд: Safco Страницы: 2

Бренд: Olympus Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды