Graco 248921 310798D Скачать руководство пользователя

Страница: 6 / 16

Setup

310798D

Connect fluid hose

Hoses are 50 ft (15.2 m) long. The maximum
combined hose length (including whip hose) is
210 ft (94.5 m).

When Using 261670 FTS, Unheated
Whip Hose

Connect desired lengths of hose.

Secure all connections as explained in
manual 309572.

Connect hoses to appropriate heater

fluid outlets.

Plug sensor cable (SC) and electrical

connector (EC) from hose heat control
into mating connectors on first length of
heated hose. See F

. 5. Be sure cables

have slack when hose bends. Wrap
cable and electrical connections with
electrical tape.

See F

. 3. Install jumper (102) in elec-

trical connector (EC) at last length of
heated hose.

Carefully extend FTS probe (P). Do not

bend or kink probe. Insert in major vol-
ume (resin) side of heated hose.

Connect hoses to FTS inlets. Connect

hose sensor cable (SC) to FTS cable.

Connect mix manifold, static mixers,

whip hose, and spray gun as explained
in separate instruction manuals.

. 3. 261670 Fluid Temperature Sensor

TI2684c

102

RES

FTS

Содержание 248921 310798D

















Результаты поиска

Содержание 248921 310798D

Отзывы:

Похожие инструкции для 248921 310798D

Бренды по названию

Популярные бренды

Graco 248921 310798D, Инструкция - Каталог запасных частей

Результаты поиска

Содержание 248921 310798D

Отзывы:

Похожие инструкции для 248921 310798D

Бренды по названию

Популярные бренды