background image

2

308813

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Tip Charts

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Accessories

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

28

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions and Mounting Hole Layout

30

. . . . . . . . . . . 

Graco Standard Warranty

32

. . . . . . . . . . . . . . . . . . . . . . 

Graco Information

32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result
in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check the equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure of the lowest rated system component. This equip-
ment has a 

4000 psi (28 MPa, 280 bar) maximum working pressure

.

Route the hoses away from the traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose Graco hoses to temperatures above 180

F (82

C) or below –40

F (–40

C).

Use only Graco approved hoses. Do not remove hose spring guards, which help protect the hose
from rupture caused by kinks or bends near the couplings.

Use fluids or solvents that are compatible with the equipment wetted parts. See the 

Technical

Data

 section of all the equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Wear hearing protection when operating this equipment.

Comply with all applicable local, state and national fire, electrical and other safety regulations.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled.

Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.

Wear the appropriate protective clothing, gloves, eyewear and respirator.

Содержание 233670

































Отзывы: