background image

Technical Data

Power Requirements

120 VAC, 60 Hz,

. . . . . . . . . . . . . . 

1 Phase, 15 AMP minimum

Pressure Operating Range

0–3000 psi

. . . . . . . . . . . . . . 

(0–21.0 MPa, 0 – 210 bar)

Maximum Delivery

0.28 GPM (1.1 liter/min)

. . . . . . . . . . 

Power Cord

No. 16 AWG, 3 wire,

. . . . . . . . . . . . . . . . . . 

8.5 feet (2.6 m) long

Inlet Paint Strainer

16 mesh

. . . . . . . . . . . . . . . . . . . . . . . . 

Fluid Outlet Nipple

1/4 npsm (m)

. . . . . . . . . . . . . . . . . . . . 

Weight – without hose and gun

33 lb (14.8 Kg)

. . . . . . . 

Dimensions

Height: 20 inch (508 mm)

. . . . . . . . . . . . . . . 

Width: 17.5 inch (444.5 mm)

Depth: 17.5 inch (444.5 mm)

Wetted Parts

Stainless Steel, Zinc-Plated Steel,

. . . . . 

Carbide, Aluminum, Nylon, Delrin

, Monel

 

Delrin

 is a registered trademark of the DuPont Company

Graco Phone Number

TO PLACE AN ORDER, contact your Graco distrib-
utor, or call this number to identify the distributor
closest to you: 1–800–367–4023 Toll Free.

Graco Inc. is registered to I.S. EN ISO 9001

The Graco Warranty and Disclaimers

Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.  With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective.  This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts.  Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect.  If the claimed defect is verified, Graco will repair or replace free of charge any defective parts.  The
equipment will be returned to the original purchaser transportation prepaid.  If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.  The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available.  Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO.
  These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer.  Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Sales Offices: Minneapolis, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan

GRACO INC.

P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

PRINTED IN U.S.A. 307–711 January

 1985, Revised August 1997

Содержание 218-501

























Отзывы: