Service
306674W
9
Displacement Pump
Before starting:
•
To reduce down time, be sure you have all neces-
sary repair parts available. Recommended spare
parts are listed in the parts list on page 15.
•
The balls (59) in the intake and piston valves cannot
be reseated on the hardened seats (68).
•
Repair Kit 239320 is available. If you have a repair
kit, use all the new parts for the best results.
•
Whenever replacing packings, also replace the
glands and bearing.
•
When cleaning parts, use a compatible solvent.
Inspect parts for wear or damage and replace as
necessary. Scoring or irregular surfaces on the
priming tube (72) or polished inner wall of the riser
tube (79) causes premature packing wear and leak-
ing. Check these parts by rubbing a finger on the
surface and by holding the parts up to the light at a
slight angle.
•
Use light, waterproof grease whenever grease is
mentioned.
Disassembly
1.
Flush the pump if possible. Follow the Pressure
Relief Procedure on page 6. Disconnect all air and
fluid hoses.
2.
Clamp the motor base in a vise. Unscrew the prim-
ing cylinder (78).
3.
Hold the priming tube (72) with a 1/4 in (6 mm)
diameter rod through the holes in the tube. Grip the
flats of the priming position (71) with a wrench and
unscrew the piston.
4.
Loosen the packing housing (70). Unscrew the riser
tube (79) from the air motor.
5.
Remove the packing housing (70) from the riser
tube (79), and remove the packings from the hous-
ing.
6.
Hold the intake valve housing (67) with a wrench,
and unscrew the priming tube (72) by inserting a 1/4
in (6 mm) diameter rod through the holes in the
tube. Handle the tube carefully to avoid marring the
surface. Remove the ball, seat, and gasket.
7.
Unscrew the intake valve housing (67) from the pis-
ton valve housing (64). Remove the ball and pack-
ings.
8.
Clean all parts thoroughly. Grease all parts except
threads when reassembling.
Reassembly
1.
One at a time, place the female gland (74), five
leather v-packings (66) with the lips of the packings
facing
up
, and the male gland (65) on the intake
housing (67). Place the gasket (62), seat (68), and
ball (59) on the housing (67).
2.
If the pins (80) were removed from the piston valve
housing (64), replace them. Hold the piston valve
housing with a wrench and screw in the intake valve
housing.
3.
Place a gasket (62), seat (68), and ball (59) on the
priming tube (72). Holding the piston valve housing
(67) with a wrench, screw the priming tube into it.
using a 1/4 in. diameter rod through the tube for
leverage.
4.
Guide the riser tube (79) over the priming tube and
screw it into the motor base, making sure the gasket
(63) is in place. Torque to 50 to 70 ft-lb (68 to 95
N.m).
5.
One at a time, place the female gland (76), five
leather packings (73) with lips of packings facing
up
,
a male gland (75), and a bearing (69) in the packing
housing (70). Screw the housing firmly into the riser
tube.
6.
Screw the priming piston (71) firmly onto the priming
tube (72). Screw the intake cylinder (78) firmly onto
the riser tube.
7.
Reconnect the ground wire if it was disconnected
during repair.
Содержание 205394
Страница 13: ...Notes 306674W 13 Notes...
