background image

Table of Contents

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INJECTION HAZARD

Spray from the valve, leaks or ruptured components can inject fluid into your body and cause ex-
tremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can
also cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medi-
cal attention
.

D

Do not point the valve at anyone or at any part of the body.

D

Do not put your hand or fingers over the valve nozzle.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Always have the trigger guard on the valve when dispensing.

D

Be sure the valve trigger safety operates before dispensing.

D

Lock the valve trigger safety when you stop dispensing.

D

Follow the Pressure Relief Procedure on page 5 if the valve nozzle clogs and before cleaning,
checking or servicing the equipment.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.

D

Know the specific hazards of the fluid you are using.

D

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.

D

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.

Содержание 204355 K Series









Отзывы: