background image

 

With the back foot in the horizontal position, slide the leg up into the 
notches indicated in the picture above. 

 

 Tighten the back foot adjustmnet knob to secure the foot into place.

Important!

Make sure that the back foot slides into the notches before you tighten 
the hoop stand back foot knob.  If the back foot is not tightened in the 
correct position in the notches, the hoop stand 

front

 foot will not fi t 

properly into place. 

Back foot notches 

NOTE!! It should not be necessary to use force in order to pivot the foot.

IF IT IS DIFFICULT TO PIVOT THE FOOT:

1. 

Check to make sure that you have moved the foot into the correct pre-pivot position 

before attempting to pivot the foot (see picture at bottom of previous page).  Hold the foot 
in that position.  Do not allow the foot to move from that position as you pivot the foot 
clockwise.  If the foot slips out of position during the pivoting motion, it may appear that the 
foot has become stuck.  Pivot the foot in the reverse direction, then try again to pivot the foot 
clockwise while holding the foot in position at the same time.

2. 

Check to make sure that the bolt has not yet slipped into the grooved area.  If the bolt 

has slipped into this grooved area, make sure you hold the foot so that it does not allow the 
bolt to slide into the grooved area and try to pivot the foot again.  The foot will not pivot if the 
bolt has slipped into the grooved area prematurely.

3. 

Check to make sure that you are attempting to pivot the foot in the correct direction.  

The foot will pivot so that the knob will follow the track.  Try to hold the foot even and pivot 
the foot with a gentle steady motion.

6

Содержание GraceHoop 2 2005















Отзывы: