Gossen MetraWatt METRALINE DM 41 Скачать руководство пользователя

Страница: 35 / 36

GMC-I Messtechnik GmbH

Product Support

If required please contact:

GMC-I Messtechnik GmbH

Product Support Hotline

Phone: +49 911 8602-0
Fax:

+49 911 8602-709

E-mail [email protected]

Repair and Replacement Parts Service
Calibration Center* and Rental Instrument Service

If required please contact:

GMC-I Service GmbH

Service Center

Beuthener Str. 41
90471 Nürnberg, Germany
Phone: +49 911 817718-0
Fax:

+49 911 817718-253

E-mail [email protected]
www.gmci-service.com

This address is only valid in Germany.
Please contact our representatives or subsidiaries for service in
other countries.

* DAkkS Calibration Laboratory for Measured Electrical Quantities

D-K-15080-01-01 accredited per DIN EN ISO/IEC 17025

Accredited quantities: direct voltage, direct current value, direct current resis-
tance, alternating voltage, alternating current value, AC active power, AC ap-
parent power, DC power, capacitance, frequency, temperature

Содержание METRALINE DM 41





































Результаты поиска

Содержание METRALINE DM 41

Отзывы:

Похожие инструкции для METRALINE DM 41

Бренды по названию

Популярные бренды

Gossen MetraWatt METRALINE DM 41, Руководство по эксплуатации

Результаты поиска

Содержание METRALINE DM 41

Отзывы:

Похожие инструкции для METRALINE DM 41

Бренды по названию

Популярные бренды