background image

THE GORMAN-RUPP COMPANY AND

GORMAN-RUPP OF CANADA LIMITED

12 MONTH LIMITED WARRANTY

EXTENT AND DURATION OF WARRANTY

Coverage:  

The Gorman-Rupp Company or Gorman-Rupp of Canada Limited (herein individually referred to as GR")

each individually warrant that its products and parts shall be free from defects in material and workmanship for twelve (12)
months from the date of purchase by the original end user.

Exceptions:

 

 

This Limited Warranty shall not apply to the following products and parts:  engines, motors, trade accesso-

ries and other products, components or materials not manufactured by GR. With respect to submersible pumps, the
pump and motor are an integral unit and are therefore warranted as a unit. However, with respect to the electrical
components in submersible pumps, this warranty is valid 

only

 when electrical controls for the pump have been specified

and/or provided by GR. Wear and tear on any product resulting from normal use is not covered by this Limited Warranty.

LIMITATIONS

GR’S SOLE AND EXCLUSIVE WARRANTY WITH RESPECT TO ITS PRODUCTS AND
PARTS  IS THIS LIMITED WARRANTY.  THIS LIMITED WARRANTY IS IN LIEU OF
ALL OTHER EXPRESS AND/OR IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE.

EXCLUSIVE REMEDY AND DAMAGES

The sole and exclusive remedy for breach of this Limited Warranty by GR, and the entire extent of its liability for such
breach or for damages arising and/or resulting from the use of the products and parts covered by this Limited Warranty
shall be as follows:

1.

Repair or replacement:  

If inspection shows that any GR product or part covered under this LimitedWarranty is defec-

tive in materials or workmanship, GR shall repair or replace the defective product or part at its option, without charge.
You must have properly installed, maintained and used the product or part claimed to be defective in accordance with
the maintenance schedule and/or manual which comes with the product.  

No allowance will be made for labor, trans-

portation or other charges incurred by you in connection with such repair or replacement.

2.

To obtain the above remedy:

a) Immediately notify GR at the address below of the claimed defect in materials or workmanship and provide the

serial number or date code of the product and/or part and provide a copy of the invoice or bill of sale referencing
the product and/or part by no later than the expiration date of the Limited Warranty period.

b) GR will advise whether inspection of the product and/or part will be necessary and whether and how repair or

replacement will be effected.  If inspection by GR is necessary, the product or part must be sent freight prepaid to
GR at the address stated below.  Return shipment of the repaired product or part will be F.O.B. the address stated
below.

3.

Damages:  

GR’s liability for damages for breach of this Limited Warranty shall not exceed the amount of the purchase

price of the product or part in respect to which damages are claimed.

 

IN NO EVENT SHALL GR BE

LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES FOR
BREACH OF THIS LIMITED WARRANTY OTHER THAN AS STATED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages.  Accordingly, the above
may not apply to you.  This Limited Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state and province to province.

THE GORMAN-RUPP COMPANY

GORMAN-RUPP OF CANADA LIMITED

P.O. BOX 1217

          70 Burwell Road

MANSFIELD, OH  44901−1217

 

      St. Thomas, Ontario N5P 3R7

       Phone: (419) 755−1011

Phone: (519) 631−2870

AV−05791 (02-07-06)

Содержание 13D1-(19) PPO





























Отзывы: