manualshive.com logo in svg

Gorilla Playsets Sun Palace Deluxe 723, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Sun Palace Deluxe 723 Скачать руководство пользователя страница 50

W/SQUARE HOLE

3-1/2" CARRIAGE BOLT

SWING BEAM PLATE

4 X 4 X 120"

SWING BEAM

SIDE RAIL

3/8" LOCK NUT

3/8" WASHER

BOLT CAP

SWING BEAM SIDE RAIL

STEP 11:  ATTACHING THE SWING BEAM PLATE TO THE 

1:  FIND THE 4 X 4 X 120" SWING BEAM SIDE RAIL.  NOTE THE DIFFERENCE BETWEEN THE SWING BEAM SIDE RAIL AND 

THE SIDE RAIL.  THE SWING BEAM SIDE RAIL WILL HAVE THREE MORE COUNTER SUNK HOLES ON ONE SIDE THAN THE 

SIDE RAIL.
2:  FIND THE SWING BEAM PLATE.  NOTICE THE TWO SQUARE HOLES ON THE SWING BEAM PLATE.
3:  PLACE THE SWING BEAM PLATE ON TOP OF THE SWING BEAM SIDE RAIL AND LINE UP THE THREE HOLES ON THE 

PLATE WITH THE THREE HOLES ON THE SWING BEAM SIDE RAIL.  MAKE SURE THE COUNTER-SUNK HOLES ARE ON THE 

OPPOSITE SIDE OF THE SWING BEAM PLATE.
4:  FASTEN THE SWING BEAM PLATE TO THE SWING BEAM SIDE RAIL WITH TWO 3-1/2" CARRIAGE BOLTS.  THE 

SQUARE NECK OF THE CARRIAGE BOLT WILL FIT INSIDE THE SQUARE HOLES OF THE SWING BEAM PLATE.  NO 

WASHER IS NEEDED.
5:  FINISH INSTALLING THE SWING BEAM PLATE TO THE SWING BEAM SIDE RAIL WITH 3/8" WASHERS, AND 3/8" LOCK 

NUTS.  INSTALL BOLT CAPS OVER ANY EXPOSED THREADS.

42

Содержание Sun Palace Deluxe 723






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды