manualshive.com logo in svg

Gorilla Playsets Sun Palace Deluxe 723, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Sun Palace Deluxe 723 Скачать руководство пользователя страница 122

21.50"

21.50"

18"

18"

18"

18"

18"

18"

STEP 16: ANGLE SUPPORTS

1: FIND SIX 2 X 4 X 18.00" ANGLE SUPPORTS AND MOUNT THEM UNDER THE DECK ON THE FRONT, REAR AND SIDES 

OF THE FORT. 

THE TOP OF THE ANGLE SUPPORTS SHOULD BE FLUSH OR LOWER THAN THE BOTTOM OF THE DECK 

BOARDS. 

AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE ANGLE SUPPORTS INTO THE DECK SUPPORTS. AT THE 

BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE SUPPORT TO THE CORNER POST OR 

MIDDLE POST.
2: FIND TWO 2 X 4 X 21.50" ANGLE SUPPORTS AND MOUNT THEM UNDER THE DECK BOARDS (

THE TOP OF THE ANGLE 

SUPPORT SHOULD BE FLUSH OR LOWER THAN THE BOTTOM OF THE DECK BOARD

) ON ONE SIDE, AND UNDER THE 

SLIDE BLOCK (

THE TOP OF THE ANGLE SUPPORT SHOULD BE FLUSH TO THE BOTTOM OF THE SLIDE BLOCK

) ON THE 

OTHER SIDE. AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE DECK SUPPORT INTO THE ANGLE SUPPORT ON 

ONE SIDE AND ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE TOP OF THE ANGLE SUPPORT TO THE SLIDE 

BLOCK ON THE OTHER SIDE . AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE 

SUPPORT TO THE CORNER POSTS. 

FOLLOW THE DIAGRAM BELOW TO IDENTIFY THE ANGLE SUPPORTS.

2 X 4 X 18.00" ANGLE SUPPORT

2" WOOD SCREW
3" WOOD SCREW

3" WOOD SCREW
2" WOOD SCREW

2-1/2" WOOD SCREWS

3" WOOD SCREW

2" WOOD SCREW

ANGLE SUPPORT

2 X 4 X 21.50" 

SLIDE BLOCK

3" WOOD SCREW

2-1/2" WOOD SCREWS

ANGLE SUPPORT

3" WOOD SCREW

2" WOOD SCREW

2 X 4 X 18.00"

ANGLE SUPPORT

2 X 4 X 18.00"

WOOD SCREWS

2-1/2" 

2" WOOD SCREW

2 X 4 X 18.00" ANGLE SUPPORT

2-1/2" WOOD SCREWS

3" WOOD SCREW

2" WOOD SCREW

2-1/2" WOOD SCREWS

2" WOOD SCREW

3" WOOD SCREW

ANGLE SUPPORT

2 X 4 X 21.50" 

DECK SUPPORT

114

Содержание Sun Palace Deluxe 723






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды