manualshive.com logo in svg

Gorilla Playsets Sun Palace Deluxe 723, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Sun Palace Deluxe 723 Скачать руководство пользователя страница 46

FINAL POSITION OF FRAME

5/16" WASHER

HEX BOLT

5/16 X 4"

2 X 6 X 79-1/4"

OUTER FORT SUPPORT

POSITION OF LADDER AND ROCK WALL

ASSEMBLIES (SEE SUB-STEP 2)

STEP 7:  INSTALLING OUTER FORT SUPPORTS

1:  FIND THE TWO 2 X 6 X 79-1/4" OUTER FORT SUPPORTS.  THE EASIEST WAY TO DIFFERENTIATE THE OUTER SUPPORTS 

FROM THE INNER SUPPORTS IS TO LOOK FOR THE COUNTER-SUNK HOLES AT 12-1/4" FROM EACH END.  THE TWO 

BOARDS WITH THE HOLES CLOSEST TO THE BOTTOM (LONGER) SIDE ARE THE OUTER FORT SUPPORTS, THE BOARDS 

WITH THE HOLES CLOSEST TO THE TOP (SHORTER) SIDE ARE THE INNER FORT SUPPORTS.
2:  LAY THE LADDER ASSEMBLY AND ROCK WALL ASSEMBLY FLAT ON THE GROUND, AND LINE UP THE 3/8" HOLE 

CLOSEST TO THE TOP WITH THE TOP HOLE OF THE OUTER FORT SUPPORT.
3:  ATTACH THE OUTER FORT SUPPORT TO THE LADDER AND ROCK WALL ASSEMBLY WITH 5/16 X 4" HEX BOLTS AND 

5/16" WASHERS.
4:  REPEAT STEPS 2 AND 3 TO FASTEN THE OUTER FORT SUPPORT TO THE OPPOSITE SIDE OF THE FORT.
5:  WITH HELP, LIFT UP THE LADDER ASSEMBLY AND ROCK WALL ASSEMBLY SO THAT THE LADDER SIDES AND ROCK 

WALL SIDES ARE FLUSH TO THE ANGLED SIDES OF THE OUTER FORT SUPPORT.

38

Содержание Sun Palace Deluxe 723






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды