manualshive.com logo in svg

Gorilla Playsets Hemisphere 2500W, Руководство по сборке, Страница: 77 / 88

Поделиться
Скачать
Gorilla Playsets Hemisphere 2500W Скачать руководство пользователя страница 77

1

1

2

2

3

3

ROOF PEAK

FIRST ROOF BOARD

PLACE THE TONGUE OF THIS BOARD 

INTO THE GROOVE OF THE ROOF PEAK.

THEN INSTALL 1-1/2" WOOD SCREWS IN 

THE TOP HOLES ONLY "1".

SECOND ROOF BOARD

PLACE THE TONGUE OF THIS 

BOARD INTO THE GROOVE OF 

THE FIRST ROOF BOARD THEN 

INSTALL 1-1/2" WOOD SCREWS IN 

THE TOP HOLES ONLY. "2"

NOW GO BACK AND 

INSTALL 1-1/2" 

WOOD SCREWS IN 

THE BOTTOM HOLES 

OF THE FIRST ROOF 

BOARD HERE. "3"

(NOT SHOWN)

THIRD ROOF BOARD

THERE ARE SEVEN 1 X 5 X 57" ROOF BOARDS ON EACH SIDE OF THE ROOF.

6) REPEAT  THIS PROCESS FOR THE REST OF THE ROOF BOARDS ON EACH SIDE OF THE ROOF.  

STEP 40: ROOF BOARDS

DUE TO THE CURVATURE OF THE ROOF SUPPORTS IT IS NECESSARY TO INSTALL THE ROOF 

BOARDS IN A CERTAIN WAY.

1) FIRST PLACE THE TONGUE OF THE FIRST ROOF BOARD INTO THE GROOVE OF THE ROOF 

PEAK.  NOW SECURE THE TOP HOLES OF THE FIRST ROOF BOARD TO THE ROOF SUPPORTS WITH 

#8 X 1-1/2" WOOD SCREWS.

2) SECOND PLACE THE TONGUE OF THE SECOND ROOF BOARD INTO THE GROOVE OF THE 

FIRST ROOF BOARD.  NOW SECURE THE TOP HOLES OF THE SECOND ROOF BOARD TO THE 

ROOF SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS. 

3) THIRD GO BACK AND SECURE THE BOTTOM HOLES OF THE FIRST ROOF BOARD TO THE ROOF 

SUPPORTS.

4) NOW PLACE THE TONGUE OF THE THIRD ROOF BOARD (NOT SHOWN) INTO THE GROOVE 

OF THE SECOND ROOF BOARD.  SECURE THE TOP HOLES OF THE THIRD ROOF BOARD TO THE 

ROOF SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS.

5) GO BACK AND SECURE THE BOTTOM HOLES OF THE SECOND ROOF BOARD TO THE ROOF 

SUPPORTS.

69

Содержание Hemisphere 2500W

























































































Отзывы:

Нет отзывов