manualshive.com logo in svg

Gorilla Playsets Hemisphere 2500W, Руководство по сборке, Страница: 74 / 88

Поделиться
Скачать
Gorilla Playsets Hemisphere 2500W Скачать руководство пользователя страница 74

SUN RAY

SUN RAY

5/4 X 2 X 16"

SUN RAY

5/4 X 2 X 13"

SUN RAY

5/4 X 2 X 16"

5/4 X 2 X 13"

TOPS OF RAYS

MUST NOT PROTRUDE 

ABOVE ROOF SUPPORTS 

OR THEY WILL INTERFERE

WITH THE ROOF BOARDS.

#8 X 1-3/4"

WOOD SCREW

(2 PER RAY)

 34° 

 81° 

 71° 

 55° 

STEP 38: SUN RAYS

1: ALL THE SUN RAY PIECES GET INSTALLED ONTO THE INSIDE SURFACE OF THE ROOF SUPPORTS AND SUN PIECE.

2: START FROM THE RIGHT SIDE OF THE FORT PLACING THE 13" SUN RAY AT AN APPROXIMATE 34  ANGLE FROM THE CENTER 

POST, SECURE WITH TWO #8 X 1-3/4" WOOD SCREWS .

3: PLACE THE SECOND 13" SUN RAY AT AN APPROXIMATE 55  ANGLE FROM THE CENTER POST, SECURE WITH TWO #8 X 1-3/4" 

WOOD SCREWS.

4: PLACE THE THIRD 13" SUN RAY AT ABOUT A 71  ANGLE FROM THE CENTER POST, SECURE WITH TWO #8 X 1-3/4" WOOD 

SCREWS.

5: PLACE THE 16" RAY AT ABOUT A 81  FROM THE CENTER POST, SECURE IT TO THE ROOF SUPPORT AND THE FRONT ROOF 

SUPPORT WITH #8 X 1-3/4" WOOD SCREWS.

6: MOVE TO THE OTHER SIDE OF THE CENTER POST (LEFT FRONT SIDE OF FORT) AND REPEAT SUBSTEPS 1 TO 5. 

7: REPEAT SUBSTEPS 1 TO 6 FOR THE REAR ROOF WALL OF THE PLAY SET.

66

Содержание Hemisphere 2500W

























































































Отзывы:

Нет отзывов