manualshive.com logo in svg

Gorilla Playsets Hemisphere 2500W, Руководство по сборке, Страница: 55 / 88

Поделиться
Скачать
Gorilla Playsets Hemisphere 2500W Скачать руководство пользователя страница 55

TORQUE WASHER

3/8" WASHER

(UPHILL) GROUND.  IF INSTALLING ON A RELATIVELY 

CARRIAGE BOLT

LEVEL SURFACE, THIS HOLE WILL NOT BE USED.

BOLT CAP

3/8" LOCK NUT

THE HOLE ABOVE WHERE THE SWING BEAM MOUNT 

IS POSITIONED IS TO BE BE USED ONLY ON UNEVEN 

3/8" X 6-1/2"

SWING BEAM MOUNT

STEP 19: ATTACHING THE SWING BEAM MOUNT

1: THE 4 X 4 X 47-1/2" SWING BEAM MOUNT HAS COUNTER-SUNK HOLES IN THE CENTER AND ON THE ENDS. INSTALL

THE SWING BEAM MOUNT SO THAT THE COUNTER-SUNK HOLES ON EACH END OF THE BEAM FACE OUT, AND THE

COUNTER-SUNK HOLES AT THE CENTER FACE DOWN.

2: FASTEN THE SWING BEAM MOUNT TO THE CORNER POSTS USING 3/8" X 6-1/2" CARRIAGE BOLTS WITH TORQUE

WASHERS. PLACE THE CARRIAGE BOLT INTO THE TORQUE WASHER, THEN INTO THE HOLE OF THE CORNER POST 

AND SET WITH A HAMMER.   USE 3/8" WASHERS AND LOCK NUTS TO SECURE THE SWING BEAM MOUNT FROM THE

OUTSIDE.  PLACE BOLT CAPS OVER THE EXPOSED THREADS AFTER SECURING.

47

Содержание Hemisphere 2500W

























































































Отзывы:

Нет отзывов