Gorilla Playsets 1500CTC Скачать руководство пользователя страница 72

Страница: 72 / 138

HEX BOLT

5/16" WASHER

2 X 6 X 70"

5/16 X 4-1/2"

FRONT OF FORT

LEFT SIDE

FRAME

(OFFSET UP)

BOARD

(OFFSET UP)

FRONT FACE

FRONT TOP PANEL

BOARD

SANDBOX BOARD

(OFFSET UP)

2 X 6 X 70"

RIGHT SIDE

FRAME

STEP 5: FRONT FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE FRONT OF THE CORNER POSTS AT THE BOTTOM. THE HOLES IN

THE SANDBOX BOARD MUST BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" FRONT FACE BOARD WITH NOTCHES ON THE FRONT OF THE CORNER POSTS AT THE MIDDLE.

THE HOLES IN THE FRONT FACE BOARD MUST BE OFFSET UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE FRONT FACE BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 6 X 70" FRONT TOP PANEL BOARD ON THE FRONT OF THE CORNER POSTS DOWN FROM THE TOP AS

SHOWN. THE HOLES IN THE TOP PANEL BOARD MUST BE OFFSET UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE FRONT TOP PANEL BOARD

TO THE T-NUTS INSTALLED ON THE CORNER POSTS.

Содержание 1500CTC











































































































































Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды

Gorilla Playsets 1500CTC, Руководство пользователя

Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды