Gorenje DFG 602, Инструкция по монтажу и эксплуатации

Страница: 9 / 73

9
spacers Z on the sides of the hood.
- Fix the hood to the cupboard using four screws N . Fig. 8
Additional instructions for the montage
Box adjustement
The hood can be installed in cabinets with different depths,
the front of the box must always be in line with the cabinet.
For alignment adjust the back stops of the box. For box
adjustment, loosen screws “
M ” and slide square plates “ G ” as
necessary and tighten screws “ M ”. Fig. 9
Description of the hood
Fig. 1.1
1.
Light Switch
2. Motor Speed Switch
3. Illumination of the cooking surface
4. Grease Filters/grease filter support grate
5. Light Cover Supports
6. Pull-Out Drawer
Model with Grease Filter Support Grate
Opening the Grease Filter Support Grates - Fig. 2.1
a. Remove the pull-out drawer completely.
b. Push the A knobs inwards toward each other (in the
“Open” direction as indicated on the plastic knob itself).
c. To remove the grates completely, use the B spring
fasteners, which act as pins to hold the grate in place
(Fig. 3).
Model with Self-supporting Metal Filters
Removing the Grease Filters - Fig. 2.2
a. Remove the pull-out drawer completely.
b. Press the side handles C (some models are supplied with
handles Z - Fig. 2.3) towards the opposite side and
remove the filters.
Putting the Filters Back in Place
a. Remove the pull-out drawer completely and mount the
grease filter so that it covers the drawer.
b. Close the drawer and install the remaining grease filter.
Opening the Light Cover Support
a. Remove the pull-out drawer completely.
b. According to model in possession:
Lamp D with hook locks type A - Fig.2.2
Move the bracket hook locks towards each other (in
direction “Open” as printed on the plastic part of the lock).
Lamp
F with hook locks type S - Fig. 1.2
Move the hook locks as indicated by the arrows and
completely remove the lamp from the housing (Fig. 1.3).
Operation
The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Maintenance
Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Grease filter
Traps cooking grease particles.
If situated inside the support grill, it may be one of the
following types:
Paper filter must be replaced once a month or if colouring
appears on upper side, in such cases the colouring is evident
through the grill openings.
Sponge filter should be washed with hot soapy water once a
month and replaced every 5 to 6 washes.
Metallic filter must be cleaned once a month, with non
abrasive detergents, by hand or in dishwasher on low
temperature and short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
Removing the Grease Filters (for models wtih grease filter
support grates)
To remove the dirty grease filter, proceed as follows:
a. Remove the pull-out drawer completely and open the
ventilation grates that support the grease filters.
b. Remove the Q fasteners for the grease filter and remove
it (Fig. 10.1). If special metal filters have been installed,
press on the plastic springs
R to unhook them (Fig.
10.2).
c. When washing or replacing the grease filter, wash the
grate as well with warm soapy water.
d. Remount the new filter or the old one after it has dried
thoroughly.
Charcoal filter (filter version only)
It absorbs unpleasant odours caused by cooking.
The saturation of the activated charcoal occurs after more or
less prolonged use, depending on the type of cooking and the
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four mounths (or when the filter saturation indication
system – if envisaged on the model in possession – indicates
this necessity).
To fit or replace a carbon filter:
a. Request a charcoal filter from the retailer, specifying the
model and type of hood.
Caution! Some charcoal filters come covered with a plastic