background image

CONDENSING AC UNIT

SINGLE / THREE PHASE AIR CONDITIONERS
INSTALLATION & SERVICE REFERENCE

© 2010-2011 Goodman Manufacturing Company, L.P.
5151 San Felipe, Suite 500, Houston, TX 77056
www.goodmanmfg.com -or- www.amana-hac.com
P/N: IO-402E

Date:  December 2011

Fixed Orifice

CAUTION

To prevent personal injury, carefully connect and disconnect
manifold gauge hoses. Escaping liquid refrigerant can cause
burns. Do not vent refrigerant into the atmosphere. Recover all
refrigerant during system repair and before final unit disposal.

1. Purge gauge lines. Connect service gauge manifold to

base-valve service ports. Run system at least 10 min-
utes to allow pressure to stabilize.

2. Temporarily install thermometer on suction (large) line

near suction line service valve with adequate contact and
insulate for best possible reading.

3. Refer to the superheat table provided for proper system

superheat. Add charge to lower superheat or recover
charge to raise superheat.

4. Disconnect manifold set, installation is complete.

Superheat Formula = Suct. Line Temp. - Sat. Suct. Temp.

Important Safety Instructions

The following symbols and labels are used throughout this
manual to indicate immediate or potential safety hazards.  It
is the owner’s and installer’s responsibility to read and com-
ply with all safety information and instructions accompanying
these symbols.  Failure to heed safety information increases
the risk of personal injury, property damage, and/or product
damage.

HIGH VOLTAGE! 
Disconnect ALL power before servicing.
Multiple power sources may be present.
Failure to do so may cause property damage,
personal injury or death.

NOTICE

THIS UNIT IS SHIPPED WITH A NITROGEN/HELIUM
HOLDING CHARGE ONLY.  UNIT MUST BE EVACUATED
AND CHARGED PER INSTALLATION INSTRUCTIONS
WITH REFRIGERANT LISTED ON SERIAL RATING PLATE.

NOTICE

UNITS SHIPPED WITH A HOLDING CHARGE ARE
INTENDED FOR COMPONENT REPLACEMENT ONLY ON
EXISTING SYSTEMS, AND NOT INTENDED FOR USE IN
NEW SYSTEMS OR NEWLY CONSTRUCTED HOMES.

NOTICE

UNITS MUST ONLY BE USED AS REPLACEMENT
COMPONENTS FOR PRE-2010 INSTALLED SYSTEMS.

55

57

59

61

63

65

67

69

71

60

10

13

17

20

23

26

29

30

31

65

8

11

14

16

19

22

26

27

29

70

5

8

10

13

15

19

23

24

25

75

----

----

6

9

11

15

20

21

23

80

----

----

----

----

7

12

17

18

20

85

----

----

----

----

----

8

13

15

16

90

----

----

----

----

----

5

10

11

13

95

----

----

----

----

----

----

5

8

10

100

----

----

----

----

----

----

----

5

8

105

----

----

----

----

----

----

----

----

5

110

----

----

----

----

----

----

----

----

----

115

----

----

----

----

----

----

----

----

----

Indoor Wet Bulb Temperature, °F

Outdoor

Dry Bulb

Temperature, °F

SYSTEM SUPERHEAT

‡ Approximate charge shown for 15’ of 3/8” liquid line. System charge must be

adjusted per final charge adjustment (Page 7.)

Models

Nominal

Charge

 (oz.)

GSC13018

75

GSC13024

77

GSC13030

66

GSC13036

77

GSC13042

95

GSC13048

89

GSC13060

131

 

Содержание GSC13018













Отзывы: