3
Dear Homeowner, please recognize the following safety in-
formation. This information will alert you to the potential
for personal injury.
WARNING
- Indicate hazards or unsafe practices which
COULD
result in severe personal injury or death.
T
HIS
PRODUCT
CONTAINS
OR
PRODUCES
A
CHEMICAL
OR
CHEMICALS
WHICH
MAY
CAUSE
SERIOUS
ILLNESS
OR
DEATH
AND
WHICH
ARE
KNOWN
TO
THE
S
TATE
OF
C
ALIFORNIA
TO
CAUSE
CANCER
,
BIRTH
DEFECTS
OR
OTHER
REPRODUCTIVE
HARM
.
WARNING
T
O
AVOID
POSSIBLE
EQUIPMENT
DAMAGE
,
PERSONAL
INJURY
,
FIRE
OR
DEATH
,
THE
FOLLOWING
INSTRUCTIONS
MUST
BE
OBSERVED
REGARDING
UNIT
LOCATION
,
AIR
REQUIREMENTS
AND
OPERATING
PROCEDURES
.
WARNING
H
EATING
UNIT
SHOULD
NOT
BE
UTILIZED
WITHOUT
REASONABLE
,
ROUTINE
,
INSPECTION
,
MAINTENANCE
AND
SUPERVISION
. I
F
THE
BUILDING
IN
WHICH
ANY
SUCH
DEVICE
IS
LOCATED
WILL
BE
VACANT
,
CARE
SHOULD
BE
TAKEN
THAT
SUCH
DEVICE
IS
ROUTINELY
INSPECTED
,
MAINTAINED
AND
MONITORED
.
IN
THE
EVENT
THAT
THE
BUILDING
MAYBE
EXPOSED
TO
FREEZING
TEMPERATURES
AND
WILL
BE
VACANT
,
ALL
WATER
-
BEARING
PIPES
SHOULD
BE
DRAINED
,
THE
BUILDING
SHOULD
BE
PROPERLY
WINTERIZED
,
AND
THE
WATER
SOURCE
CLOSED
.
IN
THE
EVENT
THAT
THE
BUILDING
MAY
BE
EXPOSED
TO
FREEZING
TEMPERATURES
AND
WILL
BE
VACANT
,
ANY
HYDRONIC
COIL
UNITS
SHOULD
BE
DRAINED
AS
WELL
AND
,
IN
SUCH
CASE
,
ALTERNATIVE
HEAT
SOURCES
SHOULD
BE
UTILIZED
.
WARNING
I
MPORTANT
N
OTE
TO
THE
O
WNER
REGARDING
P
RODUCT
L
IMITED
W
ARRANTY
Your limited warranty certificate is supplied as a separate
document with the unit installed by your contractor. Read
the limited warranty certificate carefully to determine what
is and is not covered and keep the warranty certificate in a
safe place. If you are unable to locate the warranty certifi-
cate please contact your installing contractor or contact
customer service (877-254-4729) to obtain a copy.
Before using this manual, check the serial plate for
proper model identification.
The installation and servicing of this equipment must be
performed by qualified, experienced technicians only.
U
NIT
L
OCATION
1. The furnace area and the vicinity of any other gas appli-
ances must be kept clear and free of combustible mate-
rials, gasoline, and other flammable vapors and liquids.
Also, do not store or use flammable items such as paint,
varnish, or lacquer in the area.
2. Do not store or use chlorine or fluorine products
(bleaches, cements, strippers, aerosols) near the unit.
They can corrode the heat exchanger.
3. Do not use the furnace closet as storage for brooms,
mops, brushes and oily rags or cloths. The area must be
kept clear, clean and free of lint. Furnace must be kept
free and clear of exposed or loose insulation materials
in the area of installation. Examine the furnace area
when the furnace or additional insulation is added since
some insulation materials may be combustible.
4. Make sure the furnace is always connected to an ap-
proved vent, in good condition, to carry combustion prod-
ucts outdoors.
5. Familiarize yourself with the controls that shut off the
gas and electrical power to the furnace. If the furnace
is to be shut down at the end of the heating season,
turn off both the gas and electrical power. For safety,
always turn the gas and electrical power off before per-
forming service or maintenance on the furnace.
6. Establish a regular maintenance schedule to insure effi-
cient and safe operation of the furnace. The furnace
should be checked at the beginning of each heating and
cooling season by a qualified service technician.
T
O
AVOID
PERSONAL
INJURY
OR
FIRE
,
MINIMUM
CLEARANCES
TO
COMBUSTIBLE
SURFACES
MUST
BE
FOLLOWED
.
WARNING
7. Make certain the required clearances for the furnace
are always maintained. These clearances are listed on
the furnace clearance label. If any question develops,
contact the installer of the furnace or another qualified
servicer.
U
NIT
I
NSTALLATION
Examine the furnace installation to determine the follow-
ing:
1. All flue product carrying passages external to the fur-
nace (i.e. chimney, vent connector) are clear and free
of obstructions.
2. The vent connector is in place, slopes upward and is
physically sound without holes or excessive corrosion.
3. The return air duct connection is physically sound, sealed
to the furnace casing, and terminates outside the space
containing the furnace.
4. The physical support of the furnace is sound without
sagging, cracks, or gaps around the base so as to pro-
vide a seal between the support and the base.
5. There are no obvious signs of deterioration of the fur-
nace.
6. Check for proper burner flame performance. Flame
should extend directly outward from burners without
curling, floating, or lifting off.
Содержание GCSS960804CN
Страница 11: ...11 THIS PAGE LEFT INTENTIONALLY BLANK...
