Good Ideas Circulation Ultra 2661, Инструкция по эксплуатации

Страница: 3 / 9

PANTONE 072 C
PANTONE 123 C
2
PARTS IDENTIFICATION
1. Electrode sIlicon area for feet
2. User manual
3. Sole massage roller
4. Adapter
5. LCD screen
6. Handle
7. Electrode pads
8. Remote controller
9. Electrode wires
FUNCTIONS
The principal of our electronic muscle stimulator is to control the pulses emitted, in order to stimulate
specific target areas of the body, causing muscles to contract and relax involuntarily. Usually, when the
muscles are relaxed, a large volume of blood circulates and usually, when the muscles are contracted, a large
number of metabolites are released. These actions can help the blood circulation whilst helping to lessen the
pain or soreness, swelling, fatigue and other symptoms which may be experienced.
The intended purpose of our electronic muscle stimulator is help alleviate muscle pain, soreness, stiffness,
swelling, fatigue, aches and aid increasing blood circulation and ease of general blood flow.
• Improved ABS materials and designing, following traditional man-machine engineering technology. The
item looks very modern, fashionable and simultaneously delicate.
• Different intensity levels of electromagnetic waves which can manually be controlled, providing the
ideal result for each of the sequences selected.
• Pre-set to a 25 minutes automated time set each time it’s switched on.
• 25 massage modes for the soles of your feet and body. Each impulse massage mode will help improve
and target different symptoms in order to eliminate fatigue.
• All functions can be operated by remote control and are very easy and simple to use.
HOW TO USE THE ELECTRODE GEL PADS
1. Each electrode gel pad is 8.5cm x 5.5 cm (2.16” x 3.34”).
2. Ensure the output wire is connected to the electrode gel pads.
3. Connect the output wire to the electronic muscle stimulator.
4. Remove the protective film from the adhesive pads. DO NOT discard and reuse.
5. Attach the electrode gel pads evenly to the skin.
6. Press the on/off button for 3 seconds in order to switch the unit on. Select and adjust the stimulation
and intensity modes as desired. The display will show the selection.
7. Ensure the adhesive electrode gel pads are kept clean and free from debris. Never expose them to high
temperatures or direct sunlight.
8. If the electrode gel pads adhesiveness is insufficient or dirty, refer to the “Caution for Electrode Gel
Pads” part of these instructions.
9. The effectiveness of the electrode gel pads may decrease after multiple uses, which will then require
purchasing new ones. It is also recommended to purchase new electrode gel pads if they have not been
used for a long period or have been incorrectly stored.
10. The use of this product may produce a moderate discomfort. This effect should disappear in a few
minutes. Alternatively, lower the intensity and mode levels selected.
OPERATION
Before using, please check whether the equipment is in its original state:
MODE - intensity level displayed, SOLE - intensity level displayed and time
display shows ZERO, MODE display shows 1.
1. Put your feet on the unit.
2. Hold the on/off button for 3 seconds to turn on the unit, the LCD
screen will light up in blue.
3. You can adjust the mode by pressing “MODE & MODE “.
Maximum is the 25th mode.
4. Increase intensity by pushing the button “SOLE BODY ” or
decrease intensity by pushing the button “SOLE BODY “
5. You can adjust the modes at anytime, but once the mode is reset, the intensity will be returned to
“0”. To avoid shock from the mode, a new user should reset the intensity.
6. To terminate the massage period, user can turn off the unit anytime by pressing the on/off button for
3 seconds.
7. Please note the “BODY” buttons with the up and down symbols refer to the intensity of the pads. The
two sets of pads are to be plugged-in on the right side of the unit.
8. Also note the “MODE” buttons with the up and down symbols refer to the mode description on page
5 of the instructions. The mode functions have a pre-set time amount. If you wish to stop the mode
earlier, please use the on/off button.
9. Use the “sole massage roller” to activate the blood circulation on your feet for a couple of minutes
before selecting mode and intensity. Do not stand on it.
Support Line: 0303 031 0888
For more innovative products from Good Ideas please visit:
www.shopgoodideas.com
TO HELP WITH SET-UP, PLEASE NOTE THESE IMPORTANT POINTS:
• After the unit is connected to the mains wall socket the screen will flash once. Now you need to turn the
unit on, by ACTIVATING the screen.
• To ACTIVATE the screen, press the On/Off button for NO LESS than 3 seconds.
• You now have 20 seconds to complete your choice of settings, otherwise the unit will turn off and you will
need to Activate again by pressing the ON/OFF for no less than 3 seconds. So choose; Mode (1-25) and
intensity for the Sole (1-99) and Intensity for the Body (1-99).
• PLEASE NOTE: Whenever you change the MODE, the Intensify setting reverts to zero, so you need to reset.
• Remember, if settings are not completed within 20 seconds, the unit turns OFF and you need to Activate
again.
• For best results ensure your feet and body are clean of dead skin.
• For the foot plates to work, you need to have BOTH feet positioned at the same time.
• For the pads to work, you need to have BOTH pads on the body at the same time.