Fig. 2
Fig. 4
Fig. 3
Fig. 3
Preparation
Fixture Installation
english
DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
If you presently have dimmer
controls, you will need to remove them and replace them with regular electrical switches.
If you have a three way dimmer, you will have to replace it with a regular three way switch.
If you are unfamiliar with electrical installations, we recommend you have a qualified
electrician do your installation.
Important Safety Instructions
This light has a polarized plug (one blade is wider than the other) as a safety feature to
reduce the risk of electric shock. This plug will only fit in a polarized outlet one way. If the
plug does not fit, contact a qualified electrician. Never use with an extension cord unless
the plug can be fully inserted.
DO NOT ALTER THE PLUG.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS. IMPORTANT SAFETY INSTRUCTIONS.
WARNING:
To reduce the risk of
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. Turn off/unplug and allow to cool before replacing bulb (lamp).
2. Use only with a linear fluorescent bulb:
Bulb #F8T5 8W (G9712P-T5-WHES-I, G9712P-T5-SSES-I);
Bulb #F14T5 14W (G9724P-T5-WHES-I, G9724P-T5-SSES-I);
Bulb #F21T5 21W (G9733P-T5-WHES-I, G9733P-T5-SSES-I).
3. Handle bulb(s) with care during replacing. The glass tube of bulb is very fragile and
can break easily.
IMPORTANT:
Fluorescent bulbs are included with your Good Earth Lighting® fixture. In
order to protect the bulb during shipment, your bulb(s) may be packed in a separate area of
the packing materials. Additonally, your bulbs may already be placed into their respective
sockets, but may have a protective support collar slipped over the bulb. Do
NOT
operate
you fixture with this support collar in place. You can either cut this collar off or remove the
bulb from the sockets and slide the support collar off the bulb. Discard the support collar.
Before installation, plug fixture in to a 120V 60Hz electrical outlet to check for proper
operation. Then unplug and begin the installation.
SAVE THESE INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL THIS LAMP WHILE IT IS PLUGGED IN. THIS LAMP IS FOR
INDOOR USE ONLY.
Fig. 1
1
5
2
3
4
Remove the bulb from the fixture by placing your thumbs on the
metal ends of the bulb. While applying slight pressure on the
bulb, roll the bulb toward you until the contact pins on the ends
of the bulb disengage from the socket. Pull the bulb straight out
from the socket and set aside during mounting (
Fig. 2
).
For mounting over the wall stud, drill two small pilot holes for
the screws (
Fig. 5
). Screw both wood screws into the wooden
studs. Approximately 1/8 in. of the screw should still be
protruding from the wall.
Slide the fixture over until the narrow legs of the keyhole slots
are under the heads of the screws (
Fig. 7
). Finish tightening
the screws until they are firmly seated, and the fixture is
tightly secured to the mounting surface.
For mounting into drywall, drill 3/16 in. holes for the plastic wall
anchors (not included). Insert the plastic wall anchors into the
proper holes and tap them into place so they are flush with the
surface of your drywall. Screw all screws into the plastic
anchors (
Fig. 6
). Approximately 1/2 in. of the screw should still be protruding from the wall.
6
7
DRYWALL MOUNTING
WALL STUD MOUNTING
Remove the diffuser by pulling back and up on the top edge of
the diffuser using your fingertips (
Fig.1
).
Fig. 5
Fig. 6
Fig. 7
Place fixture up to mounting surface and mark position of
the narrow end of the keyslot holes on the mounting
surface with a pencil (
Fig. 3
). The screw hole locations
must be exact for the fixture to mount properly.
Using a small drill or nail, make two small starter holes at
the marked locations (
Fig. 4
).
- 2 -
