Golding Audio OX6111E Скачать руководство пользователя страница 3

Страница: 3 / 16

Control OUT 1 - 4 (O1 - O4)

4 x 2Amp open drain (pull to ground) control outputs that can be configured via the Output

Control files on the SD card.

If Channel 1 is not defined in the Output control file or the whole file is non-existent then

Control out 1 will behave as a RUN line, it will be active while an audio file is playing.

30v maximum

ADC

Allows external control of the volume or setting of the timers.

RS485/Sync

Allows the DMS6000 to be controlled via RS485 serial commands and the synchronisation

of multiple DMS6000 units.

Line out

1V rms into 600

unbalanced (+2.2dBu).

Speaker output (SPK OUT)

Compact Case 12V supply, 8

load 8W + 8W. 4

load 15W + 15W

Compact Case 24V supply, 8

load 13W + 13W, 4

load 27W + 27W

1U Unit, 8

load 13W + 13W, 4

load 27W + 27W

Aux Power Outputs (1U case Only)

Auxiliary 24Vdc and 12Vdc power outputs. Maximum load 1amp.

Power +/- (Compact case)

Auxiliary power output. Output voltage is the same as the Input voltage applied to the DC

jack. Can also be used as power input connection.

Содержание OX6111E

















Результаты поиска

Содержание OX6111E

Отзывы:

Бренды по названию

Популярные бренды

Golding Audio OX6111E, Руководство пользователя

Результаты поиска

Содержание OX6111E

Отзывы:

Бренды по названию

Популярные бренды