Golding Audio OX6111E Скачать руководство пользователя страница 10

Страница: 10 / 16

/Treble = 0;

Pre-set Treble boost 0-10.5dB increase

This command allows the treble boost level to be pre-set thus preventing operators from

adjusting the front panel treble control.

If this command is not used or is set to zero, the front treble control will operate as

normal.

The range for this item is 0-7 in 1.5dB steps where 7 = 10.5dB

/TrebFreq = 5;

Lowest frequency of Treble boost range

This command sets the lowest frequency of which is boosted within the Treble command

If this command is set out of the below range it will default to the closest upper or lower

limit.

The range for this item is 2-15 in 1KHz steps where 15 = 15KHz (default is 5KHz)

/Balance = 0;

Pre-set Balance

This command set the output balance between the left and right channels

If this command is not used or is set to zero, the front balance control will operate as

normal.

The range for this item is 0-255 where 1 = hard left, 255 = hard right and 128 = centre

/TestButt = 1;

Define file number to play

This command sets which file should be played when the test button is pushed.

If this command is set to 0 the test button is disabled.

The range for this item 1-255 where 1 = Play 001.mp3 and 255 = Play 255.mp3

(default is 1)

Содержание OX6111E

















Результаты поиска

Содержание OX6111E

Отзывы:

Бренды по названию

Популярные бренды

Golding Audio OX6111E, Руководство пользователя

Результаты поиска

Содержание OX6111E

Отзывы:

Бренды по названию

Популярные бренды