background image

 

II. SAFETY

 

 

 

SAFETY RULES 

 

 
• 

Do not 

attempt to use your 

LiteRider Envy

 on an escalator. Always use an elevator. 

 

• 

Do not 

carry passengers on your power chair. 

 

• 

Do not 

operate your 

LiteRider Envy,

 if it is not functioning properly. 

 

• Use 

caution

 when driving on soft or uneven surfaces such as grass, gravel and on 

decks where there is no railing. 

 

• 

Never 

drive on the roadway, except when you must cross the street. 

 

• 

Always

 cross streets at intersections and use the most direct route, making sure that 

your path is clear and that you are visible to motor traffic. 

 

• It is 

not recommended

 to drive your 

LiteRider Envy, 

up or down a step or curb that is 

higher than 1-1/2 inches. 

 

• 

Never 

back up or down a step or curb. 

 

• 

Never 

operate your 

LiteRider Envy,

 while you are under the influence of alcohol. 

 

• 

Do not 

operate or store your power chair where it will be exposed to rain, snow, mist 

and below-freezing temperatures. 

 

• 

Do not 

operate your power chair on slippery, icy or salted surfaces. 

 

• 

Never 

sit on your power chair when it is in freewheel mode and on an incline or            

decline. 

 

• 

Do not 

modify your power chair in any way that is not authorized by Golden          

Technologies, Inc. 

 

• 

Do not 

disassemble the tire. If disassembly is required, have your authorized Golden 

Technologies provider perform any necessary maintenance or repair. 

 

• 

Do not 

attempt to inflate the tires of your 

LiteRider Envy. 

Your power chair is equipped 

with foam-filled flat free tires that do not require inflation. 

 

• 

Never

 sit on your 

LiteRider Envy

 when it is being transported.

 

 

• 

Always

 fasten down your 

LiteRider Envy

 securely with an approved tie-down system 

while transporting your power chair. 

 

•  Use 

caution 

when operating your 

LiteRider Envy

 while wearing long baggie clothing or 

clothing with loose belts, which could become entangled in the wheels of the power chair.  

 

• 

Always 

keep your feet firmly on the footplate surface when operating your 

LiteRider  

Envy

 to eliminate any potential of your feet becoming entangled in the wheels of the  

power chair. 

Содержание GP162







































Отзывы: