background image

8

Hardware Installation

1.

Power off all devices including your HDMI

source(s) and HDMI display(s).

2.

Connect your HDMI source device(s) to the 2x4

HDMI 2.0 Splitter/Extender's HDMI Input

connector(s) with HDMI cable(s) (HDMI cables not

included).

3.

Connect your CAT cables between the Splitter/

Extender and CAT 6/7 Receivers.

4.

Optional: Connect an HDMI display to the HDMI

Output connector of the Splitter/Extender using

an HDMI cable (HDMI cable not included). This

connection is needed only if you require local

monitoring of the HDMI signal.

5.

Connect an HDMI display to each CAT 6/7

Receiver's HDMI Out connector with an HDMI

cable (HDMI cables not included).

6.

Optional: Connect the IR Receiver cables and the

IR Emitter cable to the IR interface ports.  This

connection is needed only if you need to control

your HDMI devices from the remote location.  See

IR Control, starting on page 11, for proper IR

connection.

7.

Plug the included power adapter into the Splitter/

Extender 's Power Jack, then plug the power adapter

into a reliable power outlet.

Note

: The CAT 6/7

Receivers do not need power adapters, they can be

powered from the Splitter/Extender over CAT

cable with PoC technology.

8.

Power on your HDMI source device(s) and HDMI

display(s).  The Splitter/Extender is ready for use.

Содержание HDExt24-HD20





























Отзывы: