Godex EZ-2 Скачать руководство пользователя страница 12

Страница: 12 / 24

4. Software Command

4.1 Introduction

There are four basic types of software commands.

One-byte only control codes, see table 3.1

Set up commands, see table 3.2

Label formatting commands, see table 3.3

Buffer mode commands, see table 3.4

The commands are expanded from Esc code (decimal 27).

The commands operate in two modes.

In the line mode, the printer acts on the command received immediately. After power on, the printer is in

the line mode.

In the buffer mode, the printer stores the lines of commands for a label into the printer buffer, then prints

multiple copies of the label without pause. Only the label formatting commands can be stored into the
printer buffer.

Sign Function

Description

♀

FF (decimal 12) Form feed

↵

CR (decimal 13) Carriage Return. This code moves the label to the next line and turn reverse printing

off.

LF (decimal 10) Line feed

Table 3.1 one-byte control codes

Function

Description

Page

Esc Dn

Set print darkness level.

Esc In

Select one of 9 country code character sets.

Esc ?n

Select one of 9 barcode types

Esc Mnn

Set left margin.

Esc Nnn

Set the form feed length (01 to 25 mm) for plain thermal paper printing.

Esc On

Adjust the stop position of the label when in strip operation.

Esc ON

Disable peeler mode.

Esc Qnnn Set stop position count (for Label and Black mark paper)

Esc qnnn

Set stop position count (for Label paper only)

Esc an

Set start position. This command is applied for micro-position adjustment.

Esc fnn

Forward the paper.

Esc Rnn

Back up the paper.

Esc Sn

Set print speed.

Esc Xn

Set the bar code X dimension

Esc xnw

Adjust the narrow bar to wide bar ratio.

Esc Fn

Select see through sensor or reflect sensor.

Esc C

Cutting paper.

Table 3.2 Setup commands

PDF created with FinePrint pdfFactory trial version

http://www.fineprint.com

Содержание EZ-2

























Результаты поиска

Содержание EZ-2

Отзывы:

Похожие инструкции для EZ-2

Бренды по названию

Популярные бренды

Godex EZ-2, Руководство пользователя

Результаты поиска

Содержание EZ-2

Отзывы:

Похожие инструкции для EZ-2

Бренды по названию

Популярные бренды