Godex EZ-2 Скачать руководство пользователя страница 23

Страница: 23 / 24

B. Troubleshooting

Problems

Recommended Solution

Power switch already turned on but
the LED does not light.

Check Power connector.

Printing stops and LED goes red.

Probably software setting or programming
problem.

Check to use the correct paper

Probably label jam, remove the stuck label

Printer is working but nothing is
printed on label.

Check the label is facing up and the paper you
use is thermal paper.

Check to choose the correct printer driver.

Make sure to choose the correct model of printer
on platen.

Label is stuck

Remove the stuck label and use soft cloth
soaked with alcohol to clean the adhesive glue.

Only part of the label got printed

Label is stuck on print head.

Probably software problem

Margins are not set properly

Printer head is not fixed in proper position,
re-positing printer head screws or clipper

Difficult to load label roll

Check if the label stuck on printer.

Remove the stuck label.

Make sure the width and thickness of label is
within the specification.

When printing out, some dots
missing

Clean printer head with alcohol. (If the label glue
is attached to printer head, please apply alcohol
to printer head; wipe with soft cloth softly.)

Replace printer head for possible damage.

Printing is not in the correct position

Check the Label Transmit Sensor, it may be
covered with dust.

Check with your label supplier; make sure they
have used the recommended backing material.

Adjust the label transmit sensor if you are an
experienced printer user.

Check the label guide, it may not be in the proper
position.

Label printing jumps to next label

Check if the label height setting is the same as
actual label height.

Check the Label Transmit sensor, it may be
covered with dust.

Printing is not very clear

Check the printer darkness setting.

Please call your agent for help if the above information can not help you.

PDF created with FinePrint pdfFactory trial version

http://www.fineprint.com

Содержание EZ-2

























Результаты поиска

Содержание EZ-2

Отзывы:

Похожие инструкции для EZ-2

Бренды по названию

Популярные бренды

Godex EZ-2, Руководство пользователя

Результаты поиска

Содержание EZ-2

Отзывы:

Похожие инструкции для EZ-2

Бренды по названию

Популярные бренды