Go Power GP-ISW-200 страница 5 Скачать руководство пользователя

Страница: 5 / 32

gpelectric.com | [page 5]

GENERAL INFORMATION

General Safety

WARNING!

Limitations on Use

CAUTION!

Equipment Damage

This equipment is NOT intended for use with life support

equipment or other medical equipment or devices.

This product is designed for indoor/compartment

installation. It must not be exposed to any liquids, moisture

of any type.

Only use components or accessories recommended or sold

by Go Power! or its authorized agents.

IMPORTANT

Do not attempt to install this equipment if it appears to

be damaged in any way. See the Warranty section for

instructions on returning the equipment.

WARNING!

Hazard to Human Life

This type of notation indicates that the

hazard could be harmful to human life.

WARNING!

Shock Hazard

Danger of shock or electrocution.

WARNING!

Burn / Fire Hazard

Danger of hot surface and/or fire.

CAUTION!

Hazard to Equipment

This type of notation indicates that

the hazard may cause damage to the

equipment.

IMPORTANT

This type of notation indicates that the

information provided is important to the

installation, operation and/or maintenance

of the equipment. Failure to follow the

recommendations in such a notation could

result in annulment of the equipment

warranty.

Содержание GP-ISW-200

































Результаты поиска

Содержание GP-ISW-200

Отзывы:

Похожие инструкции для GP-ISW-200

Бренды по названию

Популярные бренды

Go Power GP-ISW-200, Руководство пользователя

Результаты поиска

Содержание GP-ISW-200

Отзывы:

Похожие инструкции для GP-ISW-200

Бренды по названию

Популярные бренды