Go Power GP-ISW-200 Скачать руководство пользователя

Страница: 25 / 32

gpelectric.com | [page 25]

OPERATION

GP-ISW-400 LED signal

Status

LED Signal

Description

Power on

R=red, O=orange, R=red

Beep twice, LED shows red



orange



green



green

Green

Normal

LED lights in solid green

Saving mode

LED flashes green condition in

intermediate condition once

every 2 seconds

Orange

Under voltage
alarm

LED flashes orange light

slowly with 5 short beeps

every 15 seconds

Over voltage

LED flashes orange light every
0.1 seconds

Red

Over
temperature

LED flashes red light quickly
twice every 1.6 seconds

O/P short
circuit

LED lights red; following two
short beeps. Inverter shuts
down after two seconds and
restart 3 times.

O/P over load

LED lights red; following two
short beeps. Inverter shuts
down after 3 minutes and
restart 3 times.

Shut down
under voltage

LED flashes red light every 0.4
seconds, then inverter shuts
down.

Shut down over
voltage

LED flashes red light every 0.1
seconds, then inverter shut
down.

Fan alarm

LED flashes red light slowly
once and quickly twice every
1.6 seconds

Table 7. GP200 & GP350 LED status



SE400 LED signal

Status

LED Signal

Description

Green

Status

LED Signal

Description

Normal or
Power ON

LED lights in solid green

Orange

Over load

LED fast blink with two long

beeps

Over temp. /
Under temp.

(Heat sink temp. over
80

℃

or under -20

℃

)

LED slow blink

Red

Over current /
Over load

(AC output short-circuit
and over load)

LED lights in solid red with one
short beeps

Over voltage

(Input DC voltage over
spec.)

LED fast blink

Under voltage

(Input DC voltage
under spec.)

LED slow blink with one long
beeps &two short beeps

Table 8. GP400 LED status

3-1-3. AC Output



4.1 FINAL INSPECTION

1. Verify all cables / conduit runs are secured with zip ties or other non-conductive cable

clamps to prevent damage from vibration.

2. Ensure all cables that pass through walls, bulkheads or any other openings are protected

against abrasion by using strain reliefs and/or grommets.

3. Check all AC, DC and ground connections are securely tightened, and if required covered

with suitable anti-seizing grease.

4. Check all connections are secure in the main and sub panels - replace all covers.
5. If required by code, have the installation inspected by an electrical inspector.

Содержание GP-ISW-200

































Результаты поиска

Содержание GP-ISW-200

Отзывы:

Похожие инструкции для GP-ISW-200

Бренды по названию

Популярные бренды

Go Power GP-ISW-200, Руководство пользователя

Результаты поиска

Содержание GP-ISW-200

Отзывы:

Похожие инструкции для GP-ISW-200

Бренды по названию

Популярные бренды