Go!Control 2GIG-CP2 Скачать руководство пользователя страница 2

STANDARD FOR ALARM LOCATION

Smoke detectors used with this system should be installed in accordance 
with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72 (National Fire 
Protection Association , Batterymarch Park, Quincy, MA 02269) which reads as 
follows:

2-1.1.1

  Smoke alarms shall be installed outside of each separate sleeping area 

in the immediate vicinity of the bedrooms and on each additional story of the 
family living unit including basements and excluding crawl spaces and unfi nished 
attics. In new construction, a smoke alarm shall be installed in each sleeping 
room.

2-1.1.2

  For family living units with one or more split levels (i.e., adjacent levels 

with less than one full story separation between levels), a smoke alarm required by 
2-1.1.1 shall suffi ce for an adjacent lower level, including basements. (Exception: 
Where there is an intervening door between one level and the adjacent lower 
level, a smoke alarm shall be installed on the lower level.)

✔ 

Ceiling mounted smoke alarms should be located in the center of the room 
or hall, or not less than 4 inches from any wall. When the alarm is mounted 
on a wall, the top of the alarm should be 4 to 12 inches from the ceiling.

✔ 

Do not install smoke alarms where normal ambient temperatures are above 
100°F (37.8°C), or below 40°F (4°C). Also, do not locate alarm in front 
of air conditioners, heating registers, or other locations where normal air 
circulation will keep smoke from entering the detector.

A-2.5.2.1

  Smoke Detection - Are More Smoke Alarms Desirable? The required 

number of smoke alarms might not provide reliable early warning protection for 
those areas separated by a door from the areas protected by the required smoke 
alarms. For this reason, it is recommended that the householder consider the use 
of additional smoke alarms for those areas for increased protection. The additional 
areas include the basement, bedrooms, dining room, furnace room, utility room, 
and hallways not protected by the required smoke alarms. The installation of 
smoke alarms in kitchens, attics (fi nished or unfi nished), or garages is not 
normally recommended, as these locations occasionally experience conditions 
that can result in improper operation.

Smoke alarms are not to be used with detector guards unless the combination 
has been evaluated and found suitable for the purpose.

 National Fire Protection Association Standard #72

Recommendations for Smoke Detectors

THIS SECURITY SYSTEM COMPLIES WITH 

NFPA REQUIREMENTS FOR TEMPORAL 

PULSE SOUNDING OF FIRE NOTIFICATION 

APPLIANCES.

Figure 1. Smoke Alarm Locations

Содержание 2GIG-CP2



















































Отзывы: