background image

 

GOSSEN Müller & Weigert       3

vice. It must be assumed that the instrument can no longer be safely oper-
ated if damage is visibly apparent. Before placing the measuring instrument 
into service, make sure that it has been properly equipped for the required 
measuring task (correct power supply, inputs and outputs). The instrument 
version and any possible options are identified on the serial plate. If covers are 
opened or parts are removed from the instrument, voltage conducting parts 
may be exposed. Balancing, maintenance and repair of live, open instruments 
may only be performed by trained personnel who are familiar with the dangers 
involved.

 

1

Applications

 

The easy to program DIGEM 96 x 48 B5 digital indicator is a high precision 
panel mount instrument with adjustable display range. The display range can 
even be matched to the 4 to 20 mA and 0 to 20 mA measuring ranges after it 
has been installed without the use of a calibrator. The measuring instrument is 
thus suited for applications, for which on-site adjustments to the display 
range are frequently required.
The instrument can optionally be provided with two limit values. Limit value 
violations are signalled optically by means of two LEDs at the right-hand side 
of the digital display. Furthermore, each limit value is assigned to a relay with a 
changeover contact.
The measurement input is of modular design. It can be used for the following 
measuring tasks depending upon the utilized measuring module:

Direct current, 0 ... 20 mA and 4 ... 20 mA

Direct current, 4 ... 20 mA, with power supply for 24 V / 20 mA 2-wire 
measuring transducer 

Temperature measurement with Pt 100

Direct voltage from ±

 

 

 

60 mV to ±

 

 

 

200 V

Direct current from ±

 

 

 

2 mA to ±

 

 

 

200 mA

Alternating voltage from 0.2 V to 700 V

Alternating current from 2 mA to 200 mA

 

2

Mounting

 

First set the measuring instrument into the panel cutout from the front without 
the fastening tabs. The fastening tabs are then inserted from the rear into the 
slots provided for this purpose at the side panels, and are squeezed against 
the control panel. 

Содержание DIGEM 96 x 48 B5

















Отзывы: