GMP PROTOPIC III-540 Скачать руководство пользователя страница 18

Страница: 18 / 48

HOW TO USE CONTROL PANEL

③ "BURST:615" - Bursting Timing Display

Operation point for Bursting Roller. Bursting Point range is "580 ~ 660"mm (for DUAL : "760 ~ 840"mm).

NOTE :

Refer to he Explanation of Control Panel to set up the Bursting Timing.

④ "LENGTH:0635" - Paper Length Display

Displayed value means paper length. Then, put a length for lamination.
Its setting range is (for MANUAL MODE : "203 ~ 1,219"mm) (for AUTO MODE : "254 ~ 813"mm).

NOTE :

Refer to the PAPER LENGTH in Explanation of Control Panel to set up.

⑤ "SPD:03" - Roller Speed Display

To display Laminating Roller Speed. Its setting range is "1 ~ 15".

NOTE :

Refer to the SPEED in Explanation of Control Panel to set up. In initial job, start at lower speed.

⑥ "READY" - Roller Temp. Display

To display Ready for Lamination. It displays "WAIT" or "READY".

- "W"(WAIT) : Not suitable for lamination(Temp. is higher or lower for lamination).
- "R"(READY) : Good for lamination. Start lamination.

⑦ "C:0038" - Counter Display

Counter for sheet for a certain time period. It can be reset if it is required.

☞ Counter Reset :

Press "SPEED" button & "MASTER DIAL" button at the same time or turn off the power and turn it on again.

But, the previous data is not saved.

⑧ "MAN" - Feeding Display

To show feeding method. This is composed of "MAN"(Manual Feeding) & "AUTO"(Automatic Feeding).

NOTE :

To change the feeding method, refer to the MASTER DIAL in Explanation of Control Panel.

⑨ Error Message Display

When error is occurred, if the RUN button is pressed, a message is displayed. In this status, the machine cannot be operated.

NOTE :

Refer to the Error Message for display.

18/48

Содержание PROTOPIC III-540

















































Результаты поиска

Содержание PROTOPIC III-540

Отзывы:

Похожие инструкции для PROTOPIC III-540

Бренды по названию

Популярные бренды

GMP PROTOPIC III-540, Руководство пользователя

Результаты поиска

Содержание PROTOPIC III-540

Отзывы:

Похожие инструкции для PROTOPIC III-540

Бренды по названию

Популярные бренды