GMC BL1181 Скачать руководство пользователя страница 12

12

Forward/reverse switch 

This switch (4) will allow you  

to change the direction of  

the motor while the trigger  

switch is not depressed.
Drilling uses the forward mode. 

The reverse mode is intended  

for the removal of screws.

Adjustable torque

This drill is equipped with 21 

torque settings plus one drill 

setting which are controlled by 

the torque collar (2). By rotating 

the collar behind the chuck, it is 

possible to adjust the torque.
This will allow better control 

when using the drill as a 

screwdriver as it prevents over-

tightening of the screws.
For drilling, always use the  use the Drill position by aligning 

the Drill symbol with the triangular indicator on the front face 

of the drill near the torque collar.
For setting the torque position, select a low setting on 

the torque collar and align the selected symbol with the 

triangular indicator on the top of the drill. Increase gradually 

to set the correct torque. It is better to use a scrap piece of 

material if possible to set the torque.

Inserting and removing bits 

This drill has a keyless chuck, which means that a chuck 

key is not needed to secure a bit in the drill.
1. Open the chuck by holding the 

rear section of the chuck firm 

and rotating the front section 

in a anti-clockwise direction, 

sufficiently enough to allow the 

drill bit required to fully enter 

the jaws of the chuck.

2. Ensure the drill bit is fully 

inserted, so that the chuck 

jaws grip the straight section of the bit. 

3. Holding the rear section of the chuck firmly, rotate the 

front section of the chuck clock-wise until the jaws tighten 

on the drill bit. The front section of the chuck needs to be 

tightened firmly to ensure the drill bit is held securely.

4. To remove the drill bit, hold the rear section of the chuck 

firmly and rotate sharply the front section of the chuck in 

a anti-clockwise direction, sufficiently enough to allow the 

drill bit to be removed.

Adjustable side handle

1. Turn the side handle clamp 

knob (6) anti-clockwise  

to loosen the collar fully and 

slip it over the chuck (1) onto 

the drill.

2. Adjust the position of the 

side handle (5) to suit the 

application and tighten the 

side handle clamp knob (6)  

to secure it in place.

Содержание BL1181

















Отзывы: