GMC BL1181 Скачать руководство пользователя страница 10

10

Unpacking

Due to modern mass production techniques, it is unlikely 

that your GMC Power Tool is faulty or that a part is missing. 

If you find anything wrong, do not operate the tool until the 

parts have been replaced or the fault has been rectified. 

Failure to do so could result in serious personal injury.

Important information – Product care

This drill/driver uses Lithium Ion Battery Cells. Care  

MUST be taken to ensure both the safety and life of the 

pack is maintained. Ensure you have read all of the safety 

notes in the previous pages before using the drill/driver.
Safety devices and circuitry for this tool are located in 

the battery pack of this tool. The battery pack is a vital 

component, not just for the power source, but also for 

the full safety control for both the charging and also the 

tool operation. Treat the battery pack with care and within 

the guidelines of this manual. If the pack does become 

immersed in water or any fluids, or is subject to a sever 

drop etc, or it does not operate within the guidelines of  

this manual, immediately STOP using the battery pack  

and have it checked.
During operation avoid overloading the drill/driver. If 

the drill driver is overloaded it will automatically STOP. 

Overloading may occur for a number of reasons including 

when the drill driver is pushed too hard or when using a 

drill bit or attachment greater than what is specified. If you 

do overload the drill driver during operation refer to the 

“Overload” section in this manual.

Note:

 When the battery of the drill is at the lower end of the 

charge, the drill is more susceptible to the overload condition.
As mentioned above the battery pack is an integral 

component of this tool and it is fitted with thermal safety 

devices. Running the drill at close to maximum load, or 

continual resetting of the overload will cause the battery 

pack to over heat. When a preset cell temperature is 

detected, the battery pack will automatically STOP  

operating and will not restart until the battery pack has 

cooled to a safe level.

In this condition, DO NOT force cool the pack by placing in 

a freezer or similar device. Refer to the “

Overload

” section 

in this manual.
Another feature of the drill/battery pack is the 

low voltage 

cut out

 feature. This feature operates when the voltage 

drops below a pre set value. When this occurs the tool will 

automatically stop operating. To correct the situation you 

need to either insert another charged battery into the drill 

or recharge the existing battery, and then proceed with the 

drilling/driving application. 

Note:

 Attempting to restart the tool in this condition without 

either recharging the battery or installing a battery with 

charge will lead to drill restarting and then stopping again 

after only a few seconds of operation.
These safety devices have been fitted for the safety, 

reliability and life of the tool. 

Fitting and removing the battery pack

To remove the battery pack from the drill firmly press the 

battery release tabs (7) at either side of the battery pack, 

and slide the battery backward out of the tool.  
To install the battery pack, align 

rails, on the tool with the tabs 

on the battery pack and slide 

the battery pack on to the drill. 

Ensure the battery pack is sitting 

straight on the foot and correctly 

entering the runners. The battery 

should slide fully on to the drill 

foot until the battery pack “clicks” 

into position.

Содержание BL1181

















Отзывы: