GMC BL1181 Скачать руководство пользователя страница 11

11

Battery charging 

This battery is recommended for the use of a residual 

current of 30mA or less. 

•  

The battery supplied with this tool is model number 1G18LiB.

•  

The Charger Pack supplied with this tool is model 

number 1835C.

•  

The Charger Adaptor supplied with this tool is model 

number 1835LiA.

Note.

 Only use the supplied batteries, charger and adaptor.

IMPORTANT.

 Before plugging in the power supply from the 

charger to the slim line adaptor always ensure that the plug 

is switched off at the mains. 

IMPORTANT.

 The battery will be fully charged after 

approximately 3-5 hours, remove it from the adaptor after 

this time.  

Do not leave a battery charging for longer than 24 hours. 
1. Align and slide the slim line 

adaptor (10) onto the battery 

until the battery pack latches 

“click” into position. Check 

the adaptor is flush with the 

battery and there is a firm 

connection. 

2. Connect the power supply 

from the charger (9) to the slim 

line adaptor via the socket in 

the rear of the adaptor housing. 

3. Plug in the charger and switch 

on. The red LED indicator will 

show power to the adaptor and 

that charging is taking place. 

4. The battery charging time is 

approximately 3 - 5 hours to 

charge a low charged battery, but will be shorter if the 

battery is already partially charged. The red LED goes 

out when the charging cycle is complete. Turn off the 

charger power supply from the mains and then remove 

the battery from the adaptor. 

WARNING.

 Only use charger 1835C with the adaptor 

(1835LiA) that is supplied for the 1G18LiB battery pack.

To obtain the best life for the battery 

For battery storage and when the drill is not being used, it is 

advised to charge the battery to approximately half charge. 

Leaving the battery in the fully charged condition can 

shorten the cell life.
Short charging is acceptable with these cells.  
Prevent constant overloading of the drill. 
Avoid allowing lose items like screws or nails etc. to be 

stored with battery packs as these or similar items can  

short battery packs and cause a fire or explosion.
Always unplug the charger when not in use and store in  

a dry secure place. 
Avoid charging, using or storing your battery in 

temperatures below 0ºC and above 40ºC.

Using the drill

Use the forward/reverse switch 

(4) to select the direction of 

rotation, then pull the trigger 

(3). This trigger switch is an 

electronic variable speed control 

which enables the user to vary 

the speed continuously. The 

speed varies according to how far 

the trigger switch is depressed, 

the further it is depressed the 

faster the chuck will rotate and the 

lighter it is depressed, the slower 

it will rotate. 
To stop the drill, release the 

trigger switch. 

Note.

 You can only change the 

direction of rotation of the drill 

using the forward/reverse switch  

when the trigger is NOT depressed.

Содержание BL1181

















Отзывы: