background image

Dear Customer

If you require any help with your product, whether it is a
Warranty claim, spare part or user information:
Please phone our Help Line for an immediate response.
Phone 1300 880 001 in Australia or 0800 445 721 in
New Zealand.

Introduction

Your new GMC power tool will more than satisfy your
expectations. It has been manufactured under stringent
GMC Quality Standards to meet superior 
performance criteria.
You will find your new tool easy and safe to operate, and,
with proper care, it will give you many years of
dependable service.

Caution. 

Carefully read through this entire Instruction

Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance and
dependability have been given top priority to the
development of this tool, making it easy to maintain 
and operate.

Environmental protection

Recycle unwanted materials instead of
disposing of them as waste. All batteries,
tools, hoses and packaging must be sorted,
taken to the local recycling centre and
recycled or disposed of in an environmentally
safe way.

Description of symbols

The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.

Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Conforms to relevant standards for
electromagnetic compatibility.

Specifications

Nominal voltage: 230 – 240Vac ~ 50Hz

Model/Wheel

HP

Spindle speed

Grit

BG125A/1

1/5 HP

2800RPM

36

BG125A/2

1/5 HP

2800RPM

60

BG150A/1

2/5 HP

2800RPM

36

BG150A/2

2/5 HP

2800RPM

60

BG200A/1

2/3 HP

2800RPM

36

BG200A/2

2/3 HP

2800RPM

60

NTS2000A/1

1/2 HP

2800RPM

36

NTS2000A/2

1/2 HP

130RPM

100

Model/Wheel

Diameter

Width

Bore

BG125A/1

125mm

16mm

12.7mm

BG125A/2

125mm

16mm

12.7mm

BG150A/1

150mm

20mm

16mm

BG150A/2

150mm

20mm

16mm

BG200A/1

200mm

20mm

16mm

BG200A/2

200mm

20mm

16mm

NTS2000A/1

150mm

20mm

16mm

NTS2000A/2

200mm

40mm

20mm

3

Содержание BG125A














Отзывы: