background image

Contents

Warranty

2

Introduction

3

Environmental protection 

3

Description of symbols

3

Specifications

3

Safety instructions

4

Additional safety rules for bench grinders

6

Unpacking

6

Connecting to the power supply

6

Know your product

7

Fitting and adjusting the eye shields and brackets 8
Fitting the tool rests

8

Bench mounting the grinder

9

Using the on/off switch

9

Operation

9

Changing a grinding wheel (high speed wheel)

10

Changing the sharpening wheel 
(low speed wheel for model NTS2000A)

10

How to true and dress the wheels

11

Grinder adjustments

12

Maintenance

12

Lubrication

12

Cleaning

12

General inspection

12

Repairs

12

Full 2 Years Warranty

Whilst every effort is made to ensure your complete
satisfaction with this tool, occasionally, due to the mass
manufacturing techniques, a tool may not live up to our
required level of performance and you may need the
assistance of our service department.
This product is warranted for a 2-year period from the
date of the original purchase. If found to be defective in
materials or workmanship, the tool or the offending
faulty component will be replaced free of charge with
another of the same item. A small freight charge 
may apply.
The warranty replacement unit is only made available 
by returning the tool to the place of purchase with a
confirmed register receipt. Proof of purchase is essential.
We reserve the right to reject any claim where the
purchase cannot be verified.
This warranty does not include damage or defects to 
the tool caused by or resulting from abuse, accidents or
alterations. It also does not cover any bonus accessories
unless the tool is a GMC Platinum Professional model.
Please ensure that you store your receipt in a safe place.
Conditions apply to the above warranty. If you need
direction of what constitutes a free of charge warranty
claim, please review the guide given on the rear of the
Receipt Holder. An indication is given as to the types of
claim that are permissible, and those that are not.

2

Содержание BG125A














Отзывы: