Glutz SD-L F 9365 Series, Монтаж и эксплуатация

Страница: 56 / 112

SD‑L F (9365x)
0548-988-11---20_2022.01.indd
– +
dAxis
0548-988/12
Page 56 of 87
Mounting and operating instructions
7.4.1 Motional parameters (PARAMETER)
* Note:
A renewed teach-in procedure
(Teach) is required.
Parameter Description Setting range Default
Vo Opening speed (velocity open) 0...14 (5...50°/s) 6
Vc Closing speed (velocity close) 0...14 (5...50°/s) 4
TOEx Hold-open time opening element inside/outside (time hold opening element inside/outside) 0...60 s 3 s
TKey Hold-open time Key (time hold opening element Key) 0...180 s 5 s
Obst Adjustable obstacle detection
Upon reaching the adjusted number of obstacles in sequence, the drive mechanism switches to manual
operation.
1...5 5
TDelay Starting delay (time delay lock) 0,0...4,0 s 0,2 s
FDelay
Relieving force during unlocking (force delay)

only effective if TDelay is > 0
0,0...7,0 A OFF
TLock Door rectification time (time press close) 0,0...4,0 s 0,5 s
FLock
Pressing force during locking (force lock)

only effective if TLock is > 0
0,0...7,0 A 2,0 A
FSlam Accelerating function in automatic mode (force slam) 0...10 OFF
FWind Obstacle detection optimized for exterior doors (force wind) OFF
OPEN
CLOSE
BOTH
OFF
Fo Opening force (force open) 0...9 4
Fc Closing force (force close) 0...9 4
Foh Hold-open force (force open hold) 0...9 0
Fch Interlocking force (force close hold)

automatically programs FLock and FDelay if these are 0 0,0...3,5 A 0
LowEn Low-energy operation (Low-Energy)
according to EN16005
OFF
BOTH
CLOSE
OPEN
OFF
Width Width door leaf to be adjusted

only if LowEn is active 90...160 cm 100 cm
Weight Weight door leaf to be adjusted

only if LowEn is active 50...250 kg 100 kg
Ao Door leaf opening angle (angle open)
If the opening angle is changed during the operating mode OPEN, the operating mode MANUAL needs to be
selected for closing the door.
20...(190°)
Rod depending
95°
*
Rod Type of rod assembly (Rod) Lintel mounting Normal rods pushing function
Sliding rods pulling function
Sliding rods pushing function
Leaf mounting Sliding rods pushing function
Sliding rods pulling function
Normal rods pushing function
Direct drive pushing function
pulling function
STD-PH
SLI-PL
SLI-PH
WIN-PH
WIN-PL
WIN-ST
DIR-PH
DIR-PL
STD-PH
*
Invers Inverse application
In the event of a power failure/error, the door leaf is opened by spring power from any position (unless it has
not been locked). The position of the motor connector is reversed with regard to the standard drive mecha -
nism. The electric lock/holding magnet must be connected in reverse order in comparison to the standard
drive mechanism (see wiring diagram E4-0141-713_Glutz).
OFF
ON
OFF
*
dAxis Distance between rotation axis of the door hinges and the mounting level of the drive mechanism (distance
Axis).
dAxis is an approximate value. Depending on the installation situation, dAxis may have to be adapted.
-8...+25 cm
Rod depending
0/+8 cm
Rod depend.
*
Fos Limitation of the opening force
Must not be increased in Germany!
5...14 A 5 A
FTic Closing force in closed position before Teach

only visible if Invers is ON 5...14 A 5 A
Mounting plate