Glow-worm Micron 40FF Скачать руководство пользователя страница 24

Страница: 24 / 24

221899A

10 Replacement of Parts

10.12 Fan, Part No. 227033 - diagram 10.7

Refer to Section 5.3.

If top outlet installation: Remove air deflector, or it may just be
swung back by loosening the securing screws, to enable fan
assembly to be removed, see diagram 8.7 and Section 5.3.

Remove the electrical connections and disconnect the air tube.

Note: Remove the electrical connections by pulling insulation
boots only.

Remove the fan assembly securing screw at the front, then
withdraw the assembly.

The fan is secured to the flue hood by three screws.

The polarity of the electrical connections is not important.

Diagram 10.6

CLEAR
AIR TUBE

SECURING
SCREW (2)

AIR

PRESSURE

SWITCH

ELECTRICAL
CONNECTIONS

7227

Diagram 10.7

SECURING

SCREW

FAN

ASSEMBLY

ELECTRICAL

CONNECTIONS

FAN

SECURING

SCREW (3)

7165

CLEAR

AIR TUBE

11.1 Part Identification

The part number and the diagram location will help to identify the part.

11.2 Ordering

When ordering any spare parts please quote the number and description from the list together with the model name and serial number.

If ordering from the local gas undertaking also quote the GC number of the appliance and part.

11 Spare Parts

Part No

Description

Location

GC Part No

801159

Multifunctional control - 40FF

Diagram 10.4.

E24851

227033

Fan - 40FF

Diagram 10.7.

E24884

227032

Air pressure switch

Diagram 10.6.

E24881

227057

Electrical thermistor

Diagram 10.1 & 10.2.

E24871

202635

Spark electrode - 40FF

Diagram 8.6.

E24837

204697

Control knob

Diagram 10.3.

E24870

205757

Injector - 40FF

Diagram 8.5.

E24960

227098

Fuse

Diagram 10.3.

*******

227030

Control board - 40FF

Diagram 10.3.

E24877

227038

Safety temperature limiter

Diagram 10.2.

E24897

Because of our constant endeavour for improvement details may vary slightly from those in the instructions.

IMPORTANT:
REMOVE ELECTRICAL CONNECTIONS
BY GRIPPING THE BOOT ONLY

Содержание Micron 40FF

























Результаты поиска

Содержание Micron 40FF

Отзывы:

Похожие инструкции для Micron 40FF

Бренды по названию

Популярные бренды

Glow-worm Micron 40FF, Инструкция по эксплуатации

Результаты поиска

Содержание Micron 40FF

Отзывы:

Похожие инструкции для Micron 40FF

Бренды по названию

Популярные бренды