Glomstad Motor GM-2150H Скачать руководство пользователя страница 10

6

 

Installation/Operation & Maintenance Manual 
GM

 

-

 

6150H 2-POST LIFT

 

Chapter 3 SAFETY 

It is vital to read this chapter of the manual carefully 
and  from  beginning  to  end  as  it  contains  important 
information regarding the risks that the operator and 
the  maintenance  fitter  may  be  exposed  to  in  the 
eventuality that the lift is used incorrectly. 

The  following  text  contains  clear  explanations 
regarding  certain  situations  of  risk  or  danger  that 
may  arise  during  the  operation  or  maintenance  of 
the  lift,  the  safety  devices  installed  and  the  correct 
use  of  such  systems,  residual  risks  and  operative 
procedures to use (general and specific precautions 
to eliminate potential hazards). 

WARNING 

Lift  is  designed  and  built  to  lift  vehicles  and  hold 
them in the elevated position in a closed workshop. 
All other uses are unauthorized; in particular, the lift 
is not suitable for: 

 

Washing and respire work; 

 

Creating raised platforms or lifting personnel; 

 

Use as a makeshift press for crushing purpose; 

 

Use as goods lift 

 

Use  as  a  jack  for  lifting  vehicles  or  changing 
wheels. 

THE MANUFACTURE DISCLAIMS ALL LIABILITY 
FOR  INJURY  TO  PERSONS  OR  DAMAGE  TO 
VEHICLES  AND  OTHER  PCABLERTY  CAUSED 
BY THE INCORRECT AND UNAUTHORISED USE 
OF THE LIFT.

 

During  lift  and  descent  movements,  the  operator 
must  remain  in  the  command  station  as  defined  in 
figure 8. The presence of persons inside the danger 
zone  indicated  in  the  same  figure  is  strictly 
prohibited.  The  presence  of  persons  beneath  the 
vehicle during operations is permitted only when the 
vehicle is parked in the elevated position. 

DO NOT USE THE LIFT WITHOUT PROTECTION 
DEVICES OR WITH THE PROTECTION DEVICES 
INHIBITED.  FAILURE  TO  COMPLY  WITH  THESE 

REGULATIONS  CAN  CAUSE  SERIOUS  INJURY 
TO PERSONS, AND IRREPERABLE DAMAGE TO 
THE LIFT AND THE VEHICLE BEING LIFTED.

 

 

Fig. 10 Working  Area 

3.1 GENERAL PRECAUTIONS 

The operator and the maintenance fitter are required 
to  observe  the  prescriptions  of  accident  prevention 
legislation in force in the country of installation of the 
lift. 

Furthermore, the operator and the maintenance fitter 
must: 

 

Always work in the scheduled working area as 
shown in the manual; 

 

Never  remove  or  deactivate  the  guards  and 
mechanical,  electrical,  or  other  types  of  safety 
devices; 

 

Read the safety notices affixed to the machine 
and the safety information in this manual. 

In  the  manual  all  safety  notices  are  shown  as 
follows: 

DANGER: 

indicates imminent danger that can result 

in serious injury or death. 

WARNING: 

indicates  situations  and/or  types  of 

maneuvers that are unsafe and can cause injuries of 
various degrees or death. 

Содержание GM-2150H
































Отзывы: