background image

Assembly Instructions

3

Multiwatt Heater

Wall Mount Installation Instructions: 

1.  Install the unit at least 8 feet (2.4 m) away from the floor. 

This minimum distance must be maintained. 

2.  Do not install closer than 1 foot (or 0.3 m) to any adjacent 

vertical surfaces or walls.

3.  Keep at least 4.5 inches (11.5 cm) from the back wall 

(with or without using the wall hanging mounting bracket).

4.  Determine the mounting location on the wall/ceiling and 

mark the hole locations.

5.  Use a 0.48 inch(12mm) drill bit and drill (2) holes 2.75 

inches  deep.

6. Insert the expansion bolts (7) flush to wall or ceiling.
7.  Attach the mounting bracket (8) and secure with 

expansion nut (10).

Note: The bracket must be firmly attached to the wall 

before hanging the unit

8.  Hook the unit to the mounting bracket and let the unit 

hang from the mounting bracket.

9.  Insert washer (4) and hex bolt (3) through mounting bracket 

(8) and heater handle (9). Tighten with spring washer (5) 

and nut (6).

Wire Connection:

10.  Run the electrical power supply cable in flexible 

conduit and connect to the wiring compartment via 

the round hole at back of the unit.

11.  Connect the power supply wires (10 AWG) to the 

pigtail leads of the unit in the wiring compartment.

Use wire crimps to make connections to corresponding 

pigtail lead wires.
 

L1 Red  L2 White  Ground: Green

OPERATING INSTRUCTIONS HAZARD OF ELECTRIC 

SHOCK, EXPLOSION OR ARC FLASH:

•  

Apply appropriate personal protective equipment 

(PPE) and follow safe electrical work practices. 

See NFPA 70

•  Circuit breaker must be installed and serviced 

only by qualified electrical personnel.

•  Always use a properly rated voltage device to 

confirm power is off.

•  Confirm there are no materials near front or 

rear of grills. 

• Switch on the circuit breaker to turn on heater. 
•  Turn the switch to 1/2/3/4 position for heat selection. 

CONTENTS

Part Qty.

Description

1

2

Tilt adjustment knob

2

2

Rubber washer

3

1

Hex bolt M10 x 60mm L, zinc plated

4

2

Washer, 10mm, zinc plated

5

1

Spring washer

6

1

Nut

7

2

Expansion bolt

8

1

Wall hanger

9

1

Handle

10

2

Nut

Setting

240VAC

208VAC

OFF

OFF

5000W

3785W

4165W

3131W

3335W

2508W

2500W

1881W

Pigtails

Round Hole

7.5 in

7.5 in

9

1

10

10

8

2

1

1

2

5,6

3,4

3,4

5,6

7

10

7

8

7

3

4

6

5

2

Содержание 653577













Отзывы: