background image

4.3 

WARRANTY

Global Skyware

VERY SMALL APERTURE TERMINAL (VSAT) PRODUCTS

TWELVE (12) MONTH LIMITED WARRANTY

Seller warrants that all Global Skyware manufactured VSAT products are transferred rightfully and with good 

title; that they are free from any lawful security interest or other lien or encumbrance unknown to Buyer. 

Seller also warrants that for a period of twelve (12) months from the date of shipment from Seller’s factory, 

all its VSAT products shall be free from defects in material and workmanship which arise under proper and 

normal use and service. Buyer’s exclusive remedy hereunder is limited to Seller’s correction (either at its plant 

or at such other place as may be agreed upon between Seller and Buyer) of any such defects by repair or re-

placement at no cost to Buyer, except for the costs of any transportation in connection with the return of the 

defective VSAT products to be replaced or repaired, and the costs to remove and/or reinstall the products, 

which shall be borne by Buyer. The limited warranty period shall not be extended beyond its original term with 

respect to any part or parts repaired or replaced by seller hereunder.

This warranty shall not apply to VSAT products which (i) have been repaired or altered in any way so as to af-

fect stability or durability, (ii) have been subject to misuse, negligence or accident, (iii) have been damaged by 

severe weather conditions such as excessive wind, ice, storms, lightning, or other natural occurrences beyond 

Seller’s control; (iv) have presented damages, defects or nonconformances caused by improper shipping, han-

dling or storage, and (v) have not been installed, operated or maintained in 

accordance with Seller’s instructions.

Buyer shall present any claims along with the defective VSAT product(s) to Seller immediately upon failure 

Non-compliance with any part of this warranty procedure may invalidate this warranty in whole or in part.

SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, OTHER THAN AS SPECIFICALLY STATED ABOVE. EXPRESS-

LY EXCLUDED ARE ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. THE FOREGOING SHALL CONSTITUTE ALL OF SELLER’S LIABILITY (EXCEPT AS TO PATENT INFRINGEMENT) 

WITH RESPECT TO THE VSAT PRODUCTS. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY LOSS OF PROFITS 

OR REVENUE, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL, CONSEQUENTIAL OR INCI-

DENTAL DAMAGES OF ANY KIND AS A RESULT OF THE USE OF THE PRODUCTS MANUFACTURED BY SELLER, 

WHETHER USED IN ACCORDANCE WITH THE INSTRUCTIONS OR NOT.  UNDER NO CIRCUMSTANCES SHALL 

SELLER’S LIABILITY TO BUYER EXCEED THE ACTUAL SALES PRICE OF THE VSAT PRODUCTS 

HEREUNDER.

In some jurisdictions, Buyer may have other rights under certain statutes that may imply non-excludable war-

ranties. No representative is authorized to assume for Seller any other liability in connection with the VSAT 

products.

DO NOT DISCARD CONTENTS

The product in this packaging was placed in the market after August 13, 2005.  Its components must not be discarded with 

normal municipal or household waste.

Contact your local waste disposal agency for recovery, recycling, or disposal instructions.

16

Содержание 122H



















Отзывы: