Glendo 004-895, Руководство по эксплуатации и обслуживанию

Страница: 5 / 24

3 2
•
Included 24-volt power converter
USE ONLY THE SUPPLIED 24-VOLT POWER CONVERTER. The included power
converter may be connected to any properly grounded single-phase source of
AC power within a voltage range of 100 to 240 V, 50 or 60 Hz. If necessary, use
the supplied grounded 2-prong plug adapter or other suitable adapter. The power
converter must be used with a suitable grounded electrical system. Using it with an
ungrounded system could expose the equipment to electrical damage. Do not use
older generation power converters. If a replacement is needed, contact GRS or an
authorized GRS dealer to order #022-987.
DO NOT OPERATE THE MACHINE WITHOUT A COMPRESSED AIR SUPPLY.
Compressed air not only provides the handpiece with power, it lubricates internal
components including the rotary air valve. Do not add oil or any lubricant to the
compressed air supply.
•
A compatible GRS pneumatic handpiece
All GRS Standard Handpieces (and GRS Airtact Handpieces with an attached
Airtact Control System) are compatible with this system.
DO NOT USE SYSTEM 3
OR GRAVERMEISTER HANDPIECES. Please contact GRS or an authorized GRS
dealer for a complete list of compatible handpieces.
•
A graver or similar tool
A properly sharpened graver or similar tool is required to cut through the surface of
metal and other materials; use with care.
The dust created while sharpening some
tool materials may present a health risk. Please contact GRS or an authorized GRS
dealer for a list of available gravers and tools.
READ THIS MANUAL ENTIRELY
BEFORE CONNECTING TO POWER.
Damage not covered by the warranty may result from not
following the instructions and maintenance in this manual.
REQUIRED EQUIPMENT & IMPORTANT NOTES
3
•
Clean, dry, oil-free air from an air compressor
Oil-free compressors are ALWAYS RECOMMENDED. When using an oil-lubricated
compressor, install an oil‑removal fi lter (coalescing type – GRS #004‑579 or
equivalent) in the air supply line to this engraving system. Damage due to oil or
water contamination IS NOT COVERED BY WARRANTY. Even slight amounts of
oil can damage internal parts and cause erratic handpiece operation. The supplied
fi nal fi lter is not capable of removing large amounts of water, oil, or contaminants.
See Setup & Connections for mounting the supplied air fi lter to engraving system.
If compressed air supply has excessive water, oil, or contaminants, an additional
fi lter/water trap and oil‑removal fi lter (coalescing type) must be installed ahead of
the engraving system.
GraverSmith™ requires a compressed air supply with minimum pressure 45 psi (3
bar) and maximum pressure 120 psi (8 bar). The compressed air supply must have
a minimum fl ow capacity of 1.4 CFM [ft³/min] or 40 LPM [L/min]. To ensure a stable
compressed air supply, the user should consider an additional air regulator to
adjust the air pressure to 45-60 psi (3-4 bar) before it enters the GraverSmith™.
•
A sturdy surface with adequate lighting
Make use of a heavy workbench or suitable solid furniture to support this
equipment, workpiece, and any additional equipment and supplies. Adequate
lighting allows clear sight, and may help prevent accidents and reduce fatigue.
Placement of this engraving system on the bench is solely user preference and
may be determined by left or right hand use during operation.
•
Workholding device or material
For best results, using a workholding device or material is highly recommended.
Properly secure the workpiece to ensure user safety and to guard the piece from
damage while working. GRS manufactures several sizes and types of workholding
devices, such as the MagnaBlock, Positioning Vise, MicroBlock vise, Thermo-Loc
material, and the BenchMate™.
REQUIRED EQUIPMENT & IMPORTANT NOTES
(continued)
DO NOT OPERATE ENGRAVING SYSTEM
WITHOUT AN ACTIVE AIR SUPPLY CONNECTED.
The air supply lubricates the rotary valve as the air passes through the
system. No additional lubrication is required.