manualshive.com logo in svg

gledhill BMA 120 SP, Инструкции по проектированию, установке и обслуживанию

Поделиться
Скачать
gledhill BMA 120 SP Скачать руководство пользователя страница 37

Page 37

BOILERMA

TE 

A-CL

ASS

 SP

3.0 SERVICING

3.4 FAULT FINDING

Despite everyones best efforts some problems could occur and lead to complaints 
from the householder.

Complaints can be grouped into the following three main categories:-

1.  The system is noisy
2.  Hot water service is unsatisfactory
3.  Space heating is unsatisfactory

The following checks should be carried out by the installer before calling the 
manufacturer.

1.  Causes of a ‘Noisy’ System

Noisy pump operation
Check the level of water in the F & E cistern - adjust and vent the pump/system if 
necessary.
Check heating circuit pressure - fi ll it to 1.5 bar and vent if necessary.
Check the pump speed setting of the boiler/heating pump - reduce if necessary but 
ensure that the temperature rise across the system is about 11°C.
Check the operation of the 3 port valve.
Check and adjust if necessary the heating system bypass valve.
Check that the radiators are correctly balanced.

Noisy boiler operation
Check the fl ow rate through the boiler at full gas rate by measuring the temperature 
rise across the boiler.  If the temperature rise is greater than 11°C, then increase the 
pump speed. 
Check system pressure, top up the expansion vessel - and vent if necessary.
Check and vent the system if necessary.

Noise when hot water tap is opened
If the plate heat exchanger pump is noisy when the hot water tap is opened, then 
check the level of water in the F & E cistern and vent the pump if necessary.
Water hammer - loose pipework and/or tap washers.

2. Causes of ‘Unsatisfactory Hot Water Service’

Check  that the BoilerMate is full of water i.e. level of water in the F & E cistern is 
correct when system is cold.
Check boiler thermostat - this should be set at maximum.
Check that the boiler fl ow temperature is adequate when it stops fi ring.  Boilers should 
provide a fl ow temperature of 82 ± 3°C but temperatures as low as 75°C will allow the 
BoilerMate A-Class to provide a satisfactory performance.
Check that the store is charging to at least 75°C.
Check that the hot water plate heat exchanger pump stops and starts when the 
hot water tap is opened and closed.
Check that the plate heat exchanger pump is set at maximum speed.
Check that the space heating and hot water load is not greater than the boiler output 
and that the BoilerMate A-Class model is suitable for the type of dwelling.
If all the above checks are satisfactory then it is possible that the performance of 
the heat exchanger is impaired by scale.  In this case the hot water fl ow rate will be 
noticeably less than the cold water fl ow rate.  Replace with a factory exchange unit 
and re-check hot water performance.

3. Causes of ‘Unsatisfactory Space Heating’

Check the boiler thermostat - this should be 
set at maximum.
Check that the boiler fl ow temperature before 
it is turned off by its own internal thermostat 
or the store sensor is adequate - it should not 
be less than 77°C.
Check the operation and the settings of 
the heating programmer and the room 
thermostat.
Check that the boiler/heating system pump is 
working and the 3 port valve is allowing water 
to the radiator circuit.
If some rooms are not being heated properly, 
then balance the system/check the operation 
of the thermostatic radiator valves (if fi tted).

Overfl ow from Feed and Expansion Cistern

Check that the controlled level of water in the 
cistern is no higher than necessary.  Adjust if 
required.

POWERFLUSHING/CLEANING OF THE HEATING 
SYSTEM

If it is proposed to ‘powerfl ush’ the heating 
system we would recommend that the 
BoilerMate appliance is isolated from the 
heating system being cleaned.  Failure to do 
this could seriously damage the appliance.

When carrying out the work always comply 
fully with the manufacturers instructions for 
the powerfl ushing equipment being used.

If in any doubt please consult our Technical 
Helpline.

Note: If the A.C.B. board is replaced it will 
need setting to the appliance type - see 
page 10 for further details.

The  system controls/operation should then 
be checked.

If the problem cannot be resolved the switch 
emergency electric backup  should be switched 
on and operated in accordance with the 
instructions on the label fi tted to the appliance 
until the installer/manufacturer can attend.
W h e n   r e q u e s t i n g   a   v i s i t   f r o m   t h e 
manufacturer the installer must have the 
completed ‘Benchmark’  commissioning/
service record sheet to hand to enable help 
to be provided.

Содержание BMA 120 SP















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды