Glasdon ICEMASTER 25 Скачать руководство пользователя страница 8

Страница: 8 / 8

Ensure the Flow Control Lever is pushed downwards and the apertures in the base of the

Hopper are closed before filling the Hopper with the spreading material.

We recommend Glasdon Icemelt or other dry granular material. Do not use damp or

wet grit/salt and do not overload the hopper (maximum capacity approximately 25kg).

To operate the spreader, pull the Flow Control Lever upwards and push the spreader

forward. The recommended operating speed is approximately 3mph, that of a brisk

walk. The spinner plate speed and spread width are controlled by the speed at which

you push the spreader.

OPERATION:

•  Do not overfill the hopper.
•  Break up any lumps as you fill the hopper.
•  Do not fill the hopper and transport over long distances.
•

Fill the hopper at the operating location just prior to use.

OPERATING TIPS:

MAINTENANCE:

• To maximise the life of your spreader and to ensure it performs when you need it,

please maintain your spreader regularly.

• Never allow your spreading material to remain in the hopper for extended periods

of time - salt is hygroscopic, it will absorb moisture in the air and can set hard like

concrete!

•  Periodically check all fixtures and fittings for tightness.
•  Rinse/dry inside and outside of the spreader after each use.
•  Move the Flow Control Lever and Spinner Plate as you rinse to avoid build up of

material.

• Spray with maintenance spray (e.g. WD40) which will drive out highly corrosive

saltwater from the working parts and metal surfaces and will protect and lubricate.

AND ICEMASTER ARE TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON GROUP OR
IT’S SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES.

•

A planned maintenance schedule or regular inspection is recommended, replacing

components as necessary.

•

Replacement components are available from GLASDON.

•

GLASDON cannot be held responsible for claims arising from incorrect installation or

assembly, unauthorised modifications or misuse of the product.

•

Glasdon UK Limited reserve the right to alter specifications without prior notice

Issue 1 October 2014

Stock no. C000/0464

DWG

No.

14B-019-07

Glasdon U.K. Limited

Preston New Road

BLACKPOOL
Lancashire
FY5 4UL

Tel:01253 600410
Fax: 01253 792558

e-mail: [email protected]
web: www.glasdon.com

Содержание ICEMASTER 25









Результаты поиска

Содержание ICEMASTER 25

Отзывы:

Похожие инструкции для ICEMASTER 25

Бренды по названию

Популярные бренды

Glasdon ICEMASTER 25, Инструкция

Результаты поиска

Содержание ICEMASTER 25

Отзывы:

Похожие инструкции для ICEMASTER 25

Бренды по названию

Популярные бренды