6
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting is
the middle increment (3). With the app in combination with
the app remote control, the increments 1 to 5 can be selected
and sent to the detector.
Increment Sensitivity
1
very insensitive
2
insensitive
3
Standard
4
sensitive
5
very sensitive
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.
Time delay channel A light
Value range (Glamox Sensor-app)
Time delay for channel A
10 s–60 min
Control for staircase light timer switch
(0.5 s "on"/10 s "off")
Pulse
Short presence channel A light
The time delay of channel A light can be switched off sooner
if a room is occupied only for a short time. (In fully automatic
device and semi-automatic device configuration type).
Value range (Glamox Sensor-app)
The time delay is applied according to the set time delay.
Off
Short-term presence is active.
On
Time delay channel H presence
Channel H presence always switches in case of a presence,
regardless of whether configuration type is set to fully auto
-
matic device or semi-automatic. The relay contact opens if the
room is vacated only after the set time delay has expired.
Value range (Glamox Sensor-app)
Presence time delay
10 s–120 min
Switch-on delay channel H presence
The relay contact only closes when someone is present after
expiry of the set switch-on delay.
Value range (Glamox Sensor-app)
Adjustable values
0 s (no switch-on delay),
30 s, 1–10 min
Configuration type
Value range (Glamox Sensor-app)
Fully automatic device: the lighting switches on and off auto-
matically (depending on presence, absence and brightness)
auto
Semi-automatic: Lights must always be switched on manually.
Lights are automatically switched off by the presence detector
(due to absence or brightness)
man
Control input S
Control input S for manual switch on/off of channel A light
automatically detects push buttons or switches.
Several push buttons can be connected to control input S.
¾
Use light push button only with neutral conductor
connector.
Value range (Glamox Sensor-app)
Automatic detection of push button or switch. A signal that
is present for less than 0.7 s is detected as a push button.
Longer signals are evaluated as a switch.
auto
To adapt to user behaviour, the type of
the used signal transmitter can have
a fixed setting. Automatic detection is
deactivated.
When selecting the push button, ope-
ning contact or NO contact can also be
specified.
Switch
Push button (NO
contact)
Push button (ope-
ning contact)
Switch
Push button
S
Push button
O
Staircase light function
Value range (Glamox Sensor-app)
The lighting can be switched on and off manually.
Off
The lighting can be switched on, but not switched
off manually. It only switches off after the set time
delay.
On
Group address
This parameter is applied when using the LMS MG USER
REMOTE or the app remote control LMS MG PROGRAM
REMOTE BT user remote control.
A group address can be assigned to each lighting channel.
The group addresses in the detector can be programmed with
the app remote control/App or the user remote control.
Value range (Glamox Sensor-app)
Adjustable values LMS MG PROGRAM REMOTE BT
I, II, III
Adjustable values LMS MG PROGRAM REMOTE BT/
App
I–VIII, all
Adjustable values LMS MG USER REMOTE
I, II
Using the user remote control, the group addresses can be
assigned as follows:
Press the and
buttons simultaneously for at least 5 s
I
Press the and
buttons simultaneously for at least 5 s
II
With the app remote control, the group address can be
assigned without the app as follows:
Press the and
buttons at the same time for at least 5 s
I
Press button A and the
button at the same time for at least 5 s
II
Press the and
buttons at the same time for at least 5 s
III
