Glacier bay VDR2522A1, Инструкция по использованию и уходу

Страница: 20 / 26

HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con 1-855-HDGLACIER para obtener más asistencia.
7
Instalación por arriba (continuación)
8
Instalación del dispensador de jabón
Insertar el conjunto del dispensador de jabón (O) a través
Por debajo del fregadero, atornillar el dispensador de jabón (T)
al vástago del conjunto del dispensador de jabón (O). Insertar el
dispensador de jabón (Q) en el conjunto del dispensador de jabón (O).
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly (O) to the sink with
the soap dispenser mounting nut (S).
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
1
Pull
down
Squeeze
1
1
2
Topmount Installation (continued)
9
Conexión del suministro de agua
NOTA: El conducto lateral de entrada del agua caliente está
marcado con una etiqueta. Evite enrollar los cables juntos,
colocarlos cerca uno del otro y dañarlos.
Enroscar la tuerca (1) de la línea de alimentación en la
salida de la válvula de suministro de agua (2) y apretarla
con una llave. No apriete demasiado.
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly (O) to the sink with
the soap dispenser mounting nut (S).
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
1
Pull
down
Squeeze
1
1
2
Topmount Installation (continued)
10
Instalación del dispensador de jabón
suministros de agua caliente y fría. Compruebe si hay fugas.
No pierda la junta (1) en la manguera.
Sacar el conjunto de la manguera de la boquilla y extraer el cabezal de
rociado desenroscándolo de la manguera en sentido contrario de las
agujas del reloj. Asegúrese de mantener el extremo de la manguera
hacia abajo dentro del fregadero y girar el grifo a la posición “caliente”
donde mezcla el agua caliente y fría.
Deje que el agua corra por las líneas durante un minuto. Esto elimina
cualquier residuo que pueda dañar las partes internas. Compruebe si
hay fugas.
Vuelva a apretar las conexiones si es necesario, pero no las apriete
demasiado. Vuelva a instalar el cabezal de rociado a mano ajustándolo
en la manguera de rociado en sentido de las agujas del reloj.
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly (O) to the sink with
the soap dispenser mounting nut (S).
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
1
Pull
down
Squeeze
1
1
2
Topmount Installation (continued)
11
Extracción del conector rápido
Si es necesario extraer el conector rápido (1), apriete las
pestañas (2) del conector rápido y luego jale hacia abajo
para desconectarlo.
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly (O) to the sink with
the soap dispenser mounting nut (S).
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal parts.
Check for leaks.
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
1
Pull
down
Squeeze
1
1
2
Topmount Installation (continued)
Bajar
Apretar